AC164140 Microchip Technology, AC164140 Datasheet - Page 19

• Manufacturer Part Number: AC164140
• Description: MCP79410 RTCC PICtail Plus Daughter Board Memory Kits
• Manufacturer: Microchip Technology
• Series: PICtail™ Plusr

Specifications of AC164140

• Main Purpose: Timing, Real Time Clock (RTC)
• Embedded: -
• Utilized Ic / Part: MCP79410
• Primary Attributes: For Use With Explorer 16, PICDEM PIC18 Explorer, XLP DEV Board, PICkit Serial Analyzer
• Secondary Attributes: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

FIGURE 5-3:
FIGURE 5-4:
5.2.3
The EEPROM does not support a hardware write
protection pin, however, software block protection is
available to the use and is configured using the
STATUS register.
5.2.4
Read operations are initiated in the same way as write
operations with the exception that the R/W bit of the
control byte is set to one. There are three basic types
of read operations: current address read, random read,
and sequential read. The SRAM array can be read in
the same way as the EEPROM using the control byte
for the SRAM ‘1101111’ with a valid address.
5.2.4.1
The MCP7941X contains an address counter that
maintains the address of the last word accessed,
internally incremented by one. Therefore, if the
previous read access was to address n (n is any legal
address), the next current address read operation
would access data from address n + 1.
Upon receipt of the control byte with R/W bit set to one,
the MCP7941X issues an Acknowledge and transmits
the 8-bit data word. The master will not acknowledge
the transfer but does generate a Stop condition and the
MCP7941X discontinues transmission
 2011 Microchip Technology Inc.
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
Current Address Read
BLOCK PROTECTION
READ OPERATION
EE BYTE WRITE
EE PAGE WRITE
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
S
T
A
R
T
S 1 0 1 0
CONTROL
x = don’t care for 1K devices
BYTE
x = don’t care for 1K devices
1 1 1
(Figure
S 1 0 1 0
S
T
A
R
T
0
A
C
K
CONTROL
5-1).
x
BYTE
ADDRESS
Preliminary
1 1 1
BYTE
0
A
C
K
x
ADDRESS
A
C
K
FIGURE 5-1:
5.2.4.2
Random read operations allow the master to access
any memory location in a random manner. To perform
this type of read operation, first the word address must
be set. This is done by sending the word address to the
MCP7941X as part of a write operation (R/W bit set to
‘0’). After the word address is sent, the master
generates a Start condition following the Acknowledge.
This terminates the write operation, but not before the
internal Address Pointer is set. Then, the master issues
the control byte again but with the R/W bit set to a one.
The MCP7941X will then issue an Acknowledge and
transmit the 8-bit data word. The master will not
acknowledge the transfer but it does generate a Stop
condition which causes the MCP7941X to discontinue
transmission
command, the internal address counter will point to the
address location following the one that was just read.
BUS ACTIVITY
MASTER
SDA LINE
BUS ACTIVITY
BYTE
DATA BYTE 0
Random Read
A
C
K
S
S
T
A
R
T
(Figure
1
A
C
K
CURRENT ADDRESS READ
(EEPROM SHOWN)
0
CONTROL
DATA
1
BYTE
0
5-2). After a random read
DATA BYTE 7
1 1 1
MCP7941X
1
A
C
K
A
C
K
S
T
O
P
P
DS22266B-page 19
A
C
K
BYTE
DATA
S
T
O
P
P
N
O
C
A
K
S
T
O
P
P