AD5206BR10 Analog Devices Inc, AD5206BR10 Datasheet - Page 7

• Manufacturer Part Number: AD5206BR10
• Description: Digital Potentiometer (Pots) IC
• Manufacturer: Analog Devices Inc

Specifications of AD5206BR10

• Potentiometer Ic Case Style: SOIC
• Peak Reflow Compatible (260 C): No
• End To End Resistance: 10ohm
• No. Of Pots: Hex (Sextet)
• Leaded Process Compatible: No
• No. Of Pins: 24
• Mounting Type: Surface Mount
• Rohs Status: RoHS non-compliant
• Taps: 256
• Resistance (ohms): 10K
• Number Of Circuits: 6
• Temperature Coefficient: 700 ppm/°C Typical
• Memory Type: Volatile
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V, ±2.3 V ~ 2.7 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 24-SOIC (7.5mm Width)
• Resistance In Ohms: 10K
• Number Of Elements: 6
• # Of Taps: 256
• Resistance (max): 10KOhm
• Power Supply Requirement: Single/Dual
• Interface Type: Serial (3-Wire/SPI)
• Single Supply Voltage (typ): 3/5V
• Dual Supply Voltage (typ): ±2.5V
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): ±2.3V
• Dual Supply Voltage (max): ±2.7V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 24
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
Table 3. AD5204 SOIC/TSSOP/PDIP Pin Function Descriptions
Pin No.
1, 2, 12
3
4
5
6
7
8
9
10
11
13
14
15
16
17
18
19
20
21
22
23
24
Name
NC
GND
CS
PR
V
SHDN
SDI
CLK
SDO
V
B3
W3
A3
B1
W1
A1
A2
W2
B2
A4
W4
B4
DD
SS
Description
Not Connected.
Ground.
Chip Select Input (Active Low). When CS returns high, data in the serial input register is decoded based on the address
bits, and then it is loaded into the target RDAC latch.
Preset to Midscale (Active Low). This pin sets the RDAC registers to 0x80.
Positive Power Supply. This pin is specified for operation at both 3 V and 5 V. It is the sum of |V
Terminal A Open-Circuit Shutdown (Active Low Input). This pin controls VR 1 through VR 4.
Serial Data Input. Data is input MSB first.
Serial Clock Input. This pin is positive edge triggered.
Serial Data Output. This pin is an open-drain transistor and requires a pull-up resistor.
Negative Power Supply. This pin is specified for operation at both 0 V and −2.7 V. It is the sum of |V
Terminal B RDAC 3.
Wiper RDAC 3. Address = 010
Terminal A RDAC 3.
Terminal B RDAC 1.
Wiper RDAC 1. Address = 000
Terminal A RDAC 1.
Terminal A RDAC 2.
Wiper RDAC 2. Address = 001
Terminal B RDAC 2.
Terminal A RDAC 4.
Wiper RDAC 4. Address = 011
Terminal B RDAC 4.
Figure 6. AD5204 SOIC/TSSOP/PDIP Pin Configuration
2
2
2
2
.
.
.
.
SHDN
GND
SDO
CLK
V
V
SDI
NC
NC
NC
CS
PR
DD
SS
10
12
11
1
2
3
4
5
6
7
8
9
Rev. C | Page 7 of 20
NC = NO CONNECT
(Not to Scale)
AD5204
TOP VIEW
24
23
22
21
20
19
18
17
16
15
14
13
B4
W4
A4
B2
W2
A2
A1
W1
B1
A3
W3
B3
AD5204/AD5206
DD
| + |V
DD
| + |V
SS
| < 5.5 V.
SS
| < 5.5 V.