AD7685BCPZRL7 Analog Devices Inc, AD7685BCPZRL7 Datasheet - Page 15
![IC,A/D CONVERTER,SINGLE,16-BIT,CMOS,LLCC,10PIN](/photos/6/60/66049/cp-10-9_sml.jpg)
AD7685BCPZRL7
Manufacturer Part Number
AD7685BCPZRL7
Description
IC,A/D CONVERTER,SINGLE,16-BIT,CMOS,LLCC,10PIN
Manufacturer
Analog Devices Inc
Series
PulSAR®r
Datasheet
1.AD7685BCPZRL7.pdf
(28 pages)
Specifications of AD7685BCPZRL7
Design Resources
Parametric Measurement Unit and Supporting Components for PAD Appls Using AD5522 and AD7685 (CN0104) Integrated Device Power Supply for PAD with Output Voltage Range 0 V to 25 V (CN0130)
Number Of Bits
16
Sampling Rate (per Second)
250k
Data Interface
DSP, MICROWIRE™, QSPI™, Serial, SPI™
Number Of Converters
1
Power Dissipation (max)
15mW
Voltage Supply Source
Single Supply
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
10-WFDFN, CSP Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
EVAL-AD7685CBZ - BOARD EVAL FOR AD7685
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
AD7685BCPZRL7
AD7685BCPZRL7TR
AD7685BCPZRL7TR
ANALOG INPUTS
Figure 28 shows an equivalent circuit of the input structure of
the AD7685.
The two diodes, D1 and D2, provide ESD protection for the
analog inputs IN+ and IN−. Care must be taken to ensure that
the analog input signal never exceeds the supply rails by more
than 0.3 V because this will cause these diodes to begin to
forward-bias and start conducting current. These diodes can
handle a forward-biased current of 130 mA maximum. For
instance, these conditions could eventually occur when the
input buffer’s (U1) supplies are different from VDD. In such a
case, an input buffer with a short-circuit current limitation can
be used to protect the part.
This analog input structure allows the sampling of the
differential signal between IN+ and IN−. By using this
differential input, small signals common to both inputs are
rejected, as shown in Figure 29, which represents the typical
CMRR over frequency. For instance, by using IN− to sense a
remote signal ground, ground potential differences between
the sensor and the local ADC ground are eliminated.
OR IN–
80
70
60
50
40
GND
1
IN+
Figure 29. Analog Input CMRR vs. Frequency
Figure 28. Equivalent Analog Input Circuit
10
C
V
V
PIN
DD
DD
= 5V
= 2.5V
VDD
FREQUENCY (kHz)
D1
D2
100
R
1000
IN
C
IN
10000
Rev. B | Page 15 of 28
During the acquisition phase, the impedance of the analog
inputs (IN+ or IN−) can be modeled as a parallel combination
of capacitor C
of R
typically 3 kΩ and is a lumped component made up of some
serial resistors and the on resistance of the switches. C
typically 30 pF and is mainly the ADC sampling capacitor.
During the conversion phase, where the switches are opened,
the input impedance is limited to C
1-pole, low-pass filter that reduces undesirable aliasing effects
and limits the noise.
When the source impedance of the driving circuit is low, the
AD7685 can be driven directly. Large source impedances
significantly affect the ac performance, especially THD. The dc
performances are less sensitive to the input impedance. The
maximum source impedance depends on the amount of THD
that can be tolerated. The THD degrades as a function of the
source impedance and the maximum input frequency, as shown
in Figure 30.
–100
–110
–120
IN
–60
–70
–80
–90
Figure 30. THD vs. Analog Input Frequency and Source Resistance
and C
0
R
R
R
R
S
S
S
S
= 250Ω
= 100Ω
IN
= 50Ω
= 33Ω
PIN
. C
and the network formed by the series connection
PIN
25
is primarily the pin capacitance. R
FREQUENCY (kHz)
50
PIN
. R
IN
and C
75
IN
make a
AD7685
IN
IN
100
is
is