AD7895ARZ-10 Analog Devices Inc, AD7895ARZ-10 Datasheet - Page 4

• Manufacturer Part Number: AD7895ARZ-10
• Description: IC,A/D CONVERTER,SINGLE,12-BIT,BICMOS,SOP,8PIN
• Manufacturer: Analog Devices Inc

Specifications of AD7895ARZ-10

• Number Of Bits: 12
• Sampling Rate (per Second): 192k
• Data Interface: Serial
• Number Of Converters: 1
• Power Dissipation (max): 20mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Number Of Elements: 1
• Resolution: 12Bit
• Architecture: SAR
• Sample Rate: 192KSPS
• Input Polarity: Bipolar
• Input Type: Voltage
• Rated Input Volt: ±10V
• Differential Input: No
• Power Supply Requirement: Single
• Single Supply Voltage (typ): 5V
• Single Supply Voltage (min): 4.75V
• Single Supply Voltage (max): 5.25V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 20mW
• Differential Linearity Error: ±1LSB
• Integral Nonlinearity Error: ±1LSB
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC N
• Input Signal Type: Single-Ended
• Package: 8SOIC N
• Sampling Rate: 192 KSPS
• Number Of Analog Inputs: 1
• Digital Interface Type: Serial (2-Wire, 3-Wire, SPI)
• Signal To Noise Ratio: 70 dB
• Polarity Of Input Voltage: Bipolar
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD7895
Pin
No.
1
2
3
4
5
6
7
8
Pin
Mnemonic
REF IN
V
GND
SCLK
SDATA
BUSY
CONVST
V
IN
DD
Description
Voltage Reference Input. An external reference source should be connected to this pin to provide the refer-
ence voltage for the AD7895’s conversion process. The REF IN input is buffered on chip. The nominal ref-
erence voltage for correct operation of the AD7895 is +2.5 V.
Analog Input Channel. The analog input range is 10 V (AD7895-10), 2.5 V (AD7895-3) and 0 V to
+2.5 V (AD7895-2).
Analog Ground. Ground reference for track/hold, comparator, digital circuitry and DAC.
Serial Clock Input. An external serial clock is applied to this input to obtain serial data from the AD7895.
A new serial data bit is clocked out on the falling edge of this serial clock. Data is guaranteed valid for 10 ns
after this falling edge so that data can be accepted on the falling edge when a fast serial clock is used. The
serial clock input should be taken low at the end of the serial data transmission.
Serial Data Output. Serial data from the AD7895 is provided at this output. The serial data is clocked out
by the falling edge of SCLK, but the data can also be read on the falling edge of SCLK. This is possible
because data bit N is valid for a specified time after the falling edge of SCLK (data hold time) (see Figure 4).
Sixteen bits of serial data are provided with four leading zeros followed by the 12 bits of conversion data.
On the sixteenth falling edge of SCLK, the SDATA line is held for the data hold time and then is disabled
(three-stated). Output data coding is 2s complement for the AD7895-10, AD7895-3 and straight binary for
the AD7895-2.
The BUSY pin is used to indicate when the part is doing a conversion. The BUSY pin will go high on the
falling edge of CONVST and will return low when the conversion is complete.
Convert Start. Edge-triggered logic input. On the falling edge of this input, the track/hold goes into its hold
mode, and conversion is initiated. If CONVST is low at the end of conversion, the part goes into power-
down mode. In this case, the rising edge of CONVST “wakes up” the part.
Positive supply voltage, +5 V
PIN FUNCTION DESCRIPTION
REF IN
PIN CONFIGURATION
SCLK
GND
V
5%.
IN
DIP and SOIC
1
2
3
4
(Not to Scale)
TOP VIEW
AD7895
–4–
8
7
6
5
V
CONVST
BUSY
SDATA
DD
REV. 0