AD9212BCPZ-65 Analog Devices Inc, AD9212BCPZ-65 Datasheet - Page 36
![IC,A/D CONVERTER,OCTAL,10-BIT,LLCC,64PIN](/photos/6/50/65021/505-64-lfcsp_sml.jpg)
AD9212BCPZ-65
Manufacturer Part Number
AD9212BCPZ-65
Description
IC,A/D CONVERTER,OCTAL,10-BIT,LLCC,64PIN
Manufacturer
Analog Devices Inc
Datasheet
1.AD9212ABCPZRL7-40.pdf
(56 pages)
Specifications of AD9212BCPZ-65
Number Of Bits
10
Sampling Rate (per Second)
65M
Data Interface
Serial, SPI™
Number Of Converters
8
Power Dissipation (max)
833mW
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LFCSP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AD9212-65EBZ - BOARD EVALUATION FOR AD9212
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
AD9212
EVALUATION BOARD
The AD9212 evaluation board provides all the support cir-
cuitry required to operate the ADC in its various modes and
configurations. The converter can be driven differentially by using
a transformer (default) or an
driven in a single-ended fashion. Separate power pins are provided
to isolate the DUT from the drive circuitry of the AD8334. Each
input configuration can be selected by changing the connections
of various jumpers (see Figure 74 to Figure 78). Figure 70 shows
the typical bench characterization setup used to evaluate the
ac performance of the AD9212. It is critical that the signal sources
used for the analog input and clock have very low phase noise
(<1 ps rms jitter) to realize the optimum performance of the
converter. Proper filtering of the analog input signal to remove
harmonics and lower the integrated or broadband noise at the
input is also necessary to achieve the specified noise performance.
See Figure 74 to Figure 84 for the complete schematics and
layout diagrams demonstrating the routing and grounding
techniques that should be applied at the system level.
POWER SUPPLIES
This evaluation board has a wall-mountable switching power
supply that provides a 6 V, 2 A maximum output. Connect the
supply to the rated 100 V ac to 240 V ac wall outlet at 47 Hz to
63 Hz. The other end of the supply is a 2.1 mm inner diameter
jack that connects to the PCB at P701. Once on the PC board,
the 6 V supply is fused and conditioned before connecting to
three low dropout linear regulators that supply the proper bias
to each of the various sections on the board.
When operating the evaluation board in a nondefault condition,
L701 to L704 can be removed to disconnect the switching
power supply. This enables the user to bias each section of the
board individually. Use P702 to connect a different supply for
WALL OUTLET
100V AC TO 240V AC
47Hz TO 63Hz
ROHDE & SCHWARZ,
ROHDE & SCHWARZ,
2V p-p SIGNAL
SYNTHESIZER
2V p-p SIGNAL
SYNTHESIZER
SMA,
SMA,
SWITCHING
SUPPLY
POWER
BAND-PASS
FILTER
2A MAX
AD8334
6V DC
XFMR
INPUT
CLK
driver. The ADC can also be
–
5.0V
+
EVALUATION BOARD
–
1.8V
AD9212
+
Figure 70. Evaluation Board Connection
–
1.8V
Rev. D | Page 36 of 56
+
CH A TO CH H
–
3.3V
SERIAL
10-BIT
LVDS
+
SPI
each section. At least one 1.8 V supply is needed for AVDD_DUT
and DRVDD_DUT; however, it is recommended that separate
supplies be used for both analog and digital signals and that each
supply have a current capability of 1 A. To operate the evaluation
board using the VGA option, a separate 5.0 V analog supply
(AVDD_5 V) is needed. To operate the evaluation board using
the SPI and alternate clock options, a separate 3.3 V analog supply
(AVDD_3.3 V) is needed in addition to the other supplies.
INPUT SIGNALS
When connecting the clock and analog sources to the
evaluation board, use clean signal generators with low phase
noise, such as Rohde & Schwarz SMA or HP8644 signal generators
or the equivalent, as well as a 1 m, shielded, RG-58, 50 Ω coaxial
cable. Enter the desired frequency and amplitude from the ADC
specifications tables. Typically, most Analog Devices, Inc., evalu-
ation boards can accept approximately 2.8 V p-p or 13 dBm
sine wave input for the clock. When connecting the analog
input source, it is recommended to use a multipole, narrow-band,
band-pass filter with 50 Ω terminations. Good choices of such
band-pass filters are available from TTE, Allen Avionics, and
K&L Microwave, Inc. The filter should be connected directly to
the evaluation board if possible.
OUTPUT SIGNALS
The default setup uses the Analog Devices HSC-ADC-FPGA-8Z
high speed deserialization board to deserialize the digital output
data and convert it to parallel CMOS. These two channels interface
directly with the Analog Devices standard dual-channel FIFO
data capture board (HSC-ADC-EVALB-DCZ). Two of the eight
channels can then be evaluated at the same time. For more
information on the channel settings and their optional settings,
visit www.analog.com/FIFO.
HSC-ADC_FPGA-8Z
DESERIALIZATION
–
3.3V
HIGH SPEED
BOARD
+
SPI
PARALLEL
–
1.5V
10-BIT
CMOS
2-CH
+
HSC-ADC-EVALB-DCZ
FIFO DATA
CAPTURE
CONNECTION
BOARD
–
3.3V
SPI
+
USB
SPI
SOFTWARE
ANALYZER
RUNNING
AND SPI
USER
ADC
PC