AD9629-40EBZ Analog Devices Inc, AD9629-40EBZ Datasheet - Page 25
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
AD9629-40EBZ
Manufacturer Part Number
AD9629-40EBZ
Description
12 Bit 40 Msps Low Pwr ADC
Manufacturer
Analog Devices Inc
Datasheet
1.AD9629BCPZRL7-20.pdf
(32 pages)
Specifications of AD9629-40EBZ
Number Of Adc's
1
Number Of Bits
12
Sampling Rate (per Second)
40M
Data Interface
Serial, SPI™
Inputs Per Adc
1 Differential
Input Range
2 Vpp
Power (typ) @ Conditions
60.5mW @ 40MSPS
Voltage Supply Source
Analog and Digital
Operating Temperature
-40°C ~ 85°C
Utilized Ic / Part
AD9629
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
HARDWARE INTERFACE
The pins described in Table 13 constitute the physical interface
between the programming device of the user and the serial
port of the AD9629. The SCLK pin and the CSB pin function
as inputs when using the SPI interface. The SDIO pin is
bidirectional, functioning as an input during write phases
and as an output during readback.
The SPI interface is flexible enough to be controlled by
either FPGAs or microcontrollers. One method for SPI
configuration is described in detail in the AN-812 Appli-
cation Note, Microcontroller-Based Serial Port Interface
(SPI) Boot Circuit.
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK signal, the CSB signal, and the SDIO signal are typically
asynchronous to the ADC clock, noise from these signals can
degrade converter performance. If the on-board SPI bus is used for
other devices, it may be necessary to provide buffers between
this bus and the AD9629 to prevent these signals from transi-
tioning at the converter inputs during critical sampling periods.
SDIO/PDWN and SCLK/DFS serve a dual function when the
SPI interface is not being used. When the pins are strapped to
DRVDD or ground during device power-on, they are associated
with a specific function. The Digital Outputs section describes
the strappable functions supported on the AD9629.
Rev. 0 | Page 25 of 32
CONFIGURATION WITHOUT THE SPI
In applications that do not interface to the SPI control registers,
the SDIO/PDWN pin, the SCLK/DFS pin serve as standalone
CMOS-compatible control pins. When the device is powered up, it
is assumed that the user intends to use the pins as static control
lines for the power-down and output data format feature control.
In this mode, connect the CSB chip select to DRVDD, which
disables the serial port interface.
Table 14. Mode Selection
Pin
SDIO/PDWN
SCLK/DFS
SPI ACCESSIBLE FEATURES
Table 15 provides a brief description of the general features that
are accessible via the SPI. These features are described in detail
in the AN-877 Application Note, Interfacing to High Speed ADCs
via SPI. The AD9629 part-specific features are described in
detail in Table 16.
Table 15. Features Accessible Using the SPI
Feature
Modes
Offset Adjust
Test Mode
Output Mode
Output Phase
Output Delay
DRVDD
External
Voltage
AGND (default)
DRVDD
AGND (default)
Description
Allows the user to set either power-down mode or
standby mode
Allows the user to digitally adjust the converter
offset
Allows the user to set test modes to have known
data on output bits
Allows the user to set up outputs
Allows the user to set the output clock polarity
Allows the user to vary the DCO delay
Configuration
Chip power-down mode
Normal operation(default)
Twos complement enabled
Offset binary enabled
AD9629