AD9834BRUZ-REEL Analog Devices Inc, AD9834BRUZ-REEL Datasheet - Page 17
![IC,Numeric-Controlled Oscillator,1-CHANNEL,CMOS,TSSOP,20PIN,PLASTIC](/photos/6/56/65613/ru-20_sml.jpg)
AD9834BRUZ-REEL
Manufacturer Part Number
AD9834BRUZ-REEL
Description
IC,Numeric-Controlled Oscillator,1-CHANNEL,CMOS,TSSOP,20PIN,PLASTIC
Manufacturer
Analog Devices Inc
Datasheet
1.AD9834BRUZ.pdf
(36 pages)
Specifications of AD9834BRUZ-REEL
Design Resources
Amplitude Control Circuit for AD9834 Waveform Generator (CN0156)
Resolution (bits)
10 b
Master Fclk
50MHz
Tuning Word Width (bits)
28 b
Voltage - Supply
2.3 V ~ 5.5 V
Operating Temperature
-40°C ~ 105°C
Mounting Type
Surface Mount
Package / Case
20-TSSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
EVAL-AD9834EBZ - BOARD EVAL FOR AD9834
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD9834BRUZ-REEL
Manufacturer:
AD
Quantity:
1 045
Part Number:
AD9834BRUZ-REEL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
The AD9834 is a sampled signal with its output following
Nyquist sampling theorem. Specifically, its output spectrum
contains the fundamental plus aliased signals (images) that
occur at multiples of the reference clock frequency and the
selected output frequency. A graphical representation of the
sampled spectrum, with aliased images, is shown in Figure 28.
The prominence of the aliased images is dependent on the ratio
of f
prominent and of a relatively high energy level as determined
by the sin(x)/x roll-off of the quantized DAC output. In fact,
depending on the f
aliased image can be on the order of −3 dB below the
fundamental.
A low-pass filter is generally placed between the output of the
DAC and the input of the comparator to further suppress the
effects of aliased images. Obviously, consideration must be
given to the relationship of the selected output frequency and
the reference clock frequency to avoid unwanted (and unexpected)
output anomalies. To apply the AD9834 as a clock generator,
limit the selected output frequency to <33% of reference clock
frequency, and thereby avoid generating aliased signals that fall
within, or close to, the output band of interest (generally dc-
selected output frequency). This practice eases the complexity
(and cost) of the external filter requirement for the clock
generator application. Refer to the
for more information.
To enable the comparator, Bit SIGN/PIB and Bit OPBITEN in
the control resister are set to 1. This is explained further in
Table 17.
OUT
to MCLK. If ratio is small, the aliased images are very
OUT
/reference clock relationship, the first
0Hz
f
OUT
AN-837 Application Note
sin x/x ENVELOPE
IMAGE
FIRST
x = π (
f
C
SYSTEM CLOCK
–
f
OUT
f
/
f
C
f
C
)
f
Figure 28. The DAC Output Spectrum
SECOND
C
IMAGE
+
f
OUT
Rev. C | Page 17 of 36
FREQUENCY (Hz)
2
f
IMAGE
THIRD
C
–
f
OUT
REGULATOR
The AD9834 has separate power supplies for the analog and
digital sections. AVDD provides the power supply required for
the analog section, and DVDD provides the power supply for
the digital section. Both of these supplies can have a value of
2.3 V to 5.5 V and are independent of each other. For example,
the analog section can be operated at 5 V, and the digital section
can be operated at 3 V, or vice versa.
The internal digital section of the AD9834 is operated at 2.5 V.
An on-board regulator steps down the voltage applied at DVDD
to 2.5 V. The digital interface (serial port) of the AD9834 also
operates from DVDD. These digital signals are level shifted
within the AD9834 to make them 2.5 V compatible.
When the applied voltage at the DVDD pin of the AD9834 is
equal to or less than 2.7 V, Pin CAP/2.5V and Pin DVDD should
be tied together, thus bypassing the on-board regulator.
OUTPUT VOLTAGE COMPLIANCE
The AD9834 has a maximum current density, set by the R
of 4 mA. The maximum output voltage from the AD9834 is
V
the internal switch does not change, affecting the spectral
performance of the part. For a minimum supply of 2.3 V, the
maximum output voltage is 0.8 V. Specifications in Table 1 are
guaranteed with an R
2
f
DD
C
2
− 1.5 V. This is to ensure that the output impedance of
FOURTH
f
C
IMAGE
+
f
OUT
3
f
C
IMAGE
FIFTH
–
f
OUT
SET
of 6.8 kΩ and an R
3
f
C
3
f
IMAGE
C
SIXTH
+
f
OUT
LOAD
of 200 Ω.
AD9834
SET
,