ADA4858-3ACPZ-R7 Analog Devices Inc, ADA4858-3ACPZ-R7 Datasheet - Page 16

• Manufacturer Part Number: ADA4858-3ACPZ-R7
• Description: Single Supply High Spd RR Video Amp
• Manufacturer: Analog Devices Inc

Specifications of ADA4858-3ACPZ-R7

• Amplifier Type: Current Feedback
• Number Of Circuits: 3
• Slew Rate: 600 V/µs
• -3db Bandwidth: 600MHz
• Current - Input Bias: 8µA
• Voltage - Input Offset: 500µV
• Current - Supply: 19mA
• Current - Output / Channel: 21mA
• Voltage - Supply, Single/dual (±): 3 V ~ 5.5 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 16-LFCSP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Gain Bandwidth Product: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ADA4858-3ACPZ-R7TR

ADA4858-3
PD (POWER-DOWN) PIN
The ADA4858-3 is equipped with a PD (power-down) pin for
all three amplifiers. This allows the user to reduce the quiescent
supply current when an amplifier is not active. The power-
down threshold levels are derived from ground level. The
amplifiers are powered down when the voltage applied to the
PD pin is greater than a certain voltage from ground. In a 5 V
supply application, the voltage is greater than 2 V, and in a 3.3 V
supply application, the voltage is greater than 1.5 V. The amplifier
is enabled whenever the PD pin is left floating (not connected).
If the PD pin is not used, it is best to leave it floating or connected
to ground. Note that the power-down feature does not control the
charge pump output voltage and current.
Table 6. Power-Down Voltage Control
PD Pin
Not Active
Active
POWER SUPPLY BYPASSING
Careful attention must be paid to bypassing the power supply
pins of the ADA4858-3. High quality capacitors with low
equivalent series resistance (ESR), such as multilayer ceramic
capacitors (MLCCs), should be used to minimize supply
voltage ripple and power dissipation. A large, usually tantalum,
capacitor between 2.2 μF to 47 μF located in proximity to the
ADA4858-3 is required to provide good decoupling for lower
frequency signals. The actual value is determined by the circuit
transient and frequency requirements. In addition, place 0.1 μF
MLCC decoupling capacitors as close to each of the power
supply pins and across from both supplies as is physically
possible, no more than 1/8 inch away. The ground returns
should terminate immediately into the ground plane. Placing
the bypass capacitor return close to the load return minimizes
ground loops and improves performance.
5 V
<1.5 V
>2 V
3.3 V
<1 V
>1.5 V
Rev. A | Page 16 of 20
LAYOUT
As is the case with all high speed applications, careful attention
to printed circuit board (PCB) layout details prevents associated
board parasitics from becoming problematic. The ADA4858-3 can
operate at up to 600 MHz; therefore, proper RF design techniques
must be employed. The PCB should have a ground plane covering
all unused portions of the component side of the board to provide a
low impedance return path. Removing the ground plane on all
layers from the area near and under the input and output pins
reduces stray capacitance. Keep signal lines connecting the
feedback and gain resistors as short as possible to minimize the
inductance and stray capacitance associated with these traces. Place
termination resistors and loads as close as possible to their
respective inputs and outputs. Keep input and output traces as
far apart as possible to minimize coupling (crosstalk) through the
board. Adherence to microstrip or stripline design techniques for
long signal traces (greater than 1 inch) is recommended. For
more information on high speed board layout, see “A Practical
Guide to High-Speed Printed-Circuit-Board Layout, ” Analog
Dialogue, Volume 39, Number 3, September 2005 at
www.analog.com.