ADM211EARU-REEL Analog Devices Inc, ADM211EARU-REEL Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADM211EARU-REEL
Manufacturer Part Number
ADM211EARU-REEL
Description
IC,LINE TRANSCEIVER,CMOS,4 DRIVER,5 RCVR,TSSOP,28PIN,PLASTIC
Manufacturer
Analog Devices Inc
Type
Transceiverr
Datasheet
1.ADM213EARSZ-REEL.pdf
(20 pages)
Specifications of ADM211EARU-REEL
Rohs Status
RoHS non-compliant
Number Of Drivers/receivers
4/5
Protocol
RS232
Voltage - Supply
4.5 V ~ 5.5 V
Mounting Type
Surface Mount
Package / Case
28-TSSOP
Lead Free Status / RoHS Status
Table 6. Pin Function Descriptions
Mnemonic
V
V+
V–
GND
C1+, C1–
C2+, C2–
T
T
R
R
EN/EN
SHDN/SHDN
IN
OUT
CC
IN
OUT
Function
Power Supply Input (5 V ± 10%).
Internally Generated Positive Supply (+9 V nominal).
Internally Generated Negative Supply (−9 V nominal).
Ground Pin. Must be connected to 0 V.
External Capacitor 1 is connected between these pins. A 0.1 μF capacitor is recommended, but larger capacitors (up to
47 μF) can be used.
External Capacitor 2 is connected between these pins. A 0.1 μF capacitor is recommended, but larger capacitors (up to
47 μF) can be used.
Transmitter (Driver) Inputs. These inputs accept TTL/CMOS levels. An internal 400 kΩ pull-up resistor to V
each input.
Transmitter (Driver) Outputs. These are RS-232 signal levels (typically ±9 V).
Receiver Inputs. These inputs accept RS-232 signal levels. An internal 5 kΩ pull-down resistor to GND is connected on
each input.
Receiver Outputs. These are TTL/CMOS output logic levels.
Receiver Enable (active high on ADM213E, active low on ADM211E). This input is used to enable/disable the receiver
outputs. With EN = low for the ADM211E (EN = high for the ADM213E), the receiver outputs are enabled. With EN = high
for the ADM211E (EN = low for the ADM213E), the receiver outputs are placed in a high impedance state. (See Table 3
and Table 4.)
Shutdown Control (active low on ADM213E, active high on ADM211E). When the ADM211E is in shutdown, the charge
pump is disabled, the transmitter outputs are turned off, and all receiver outputs are placed in a high impedance state.
When the ADM213E is in shutdown, the charge pump is disabled, the transmitter outputs are turned off, and Receiver R1 to
Receiver R3 are placed in a high impedance state; Receiver R4 and Receiver R5 on the ADM213E continue to operate
normally during shutdown. (See Table 3 and Table 4.) Power consumption for all parts reduces to 5 μW in shutdown.
Figure 10. ADM213E Pin Configuration
R2
R1
T3
T1
T2
GND
R2
R1
T2
T1
V
C1+
C1–
OUT
OUT
OUT
OUT
OUT
V+
CC
IN
IN
IN
IN
1
ACTIVE IN SHUTDOWN.
10
11
12
13
14
1
2
3
4
5
6
7
8
9
(Not to Scale)
ADM213E
TOP VIEW
28
27
26
25
24
23
22
21
20
19
18
17
16
15
T4
R3
R3
SHDN
EN
R4
R4
T4
T3
R5
R5
V–
C2–
C2+
OUT
IN
IN
IN
OUT
IN 1
OUT 1
OUT 1
IN 1
ADM206E/ADM207E/ADM208E/ADM211E/ADM213E
Rev. E | Page 7 of 20
TTL/CMOS
OUTPUTS
TTL/CMOS
1
2
3
INPUTS
INTERNAL 400kΩ PULL-UP RESISTOR ON EACH TTL/CMOS INPUT.
INTERNAL 5kΩ PULL-DOWN RESISTOR ON EACH RS-232 INPUT.
ACTIVE IN SHUTDOWN.
1
R4
R5
R1
R2
R3
0.1µF
0.1µF
OUT 3
OUT 3
T1
T2
T3
T4
OUT
OUT
OUT
16V
16V
Figure 11. ADM213E Typical Operating Circuit
EN
IN
IN
IN
IN
+
+
12
14
15
16
20
21
26
22
19
24
6
5
7
8
C1+
C1–
C2+
C2–
+10V TO –10V
GND
+5V TO +10V
VOLTAGE
DOUBLER
INVERTER
10
VOLTAGE
T1
T2
T3
T4
R2
R4
R5
ADM213E
R1
R3
V
V+
V–
CC
11
13
17
28
27
23
18
25
4
2
3
1
9
5V INPUT
CC
is connected on
+
+
SHDN
0.1µF
6.3V
0.1µF
16V
T1
T2
T3
T4
R1
R2
R3
R4
R5
OUT
OUT
OUT
OUT
IN
IN
IN
IN 3
IN 3
RS-232
INPUTS
RS-232
OUTPUTS
+
0.1µF
2