ADM3202ARN-REEL7 Analog Devices Inc, ADM3202ARN-REEL7 Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADM3202ARN-REEL7
Manufacturer Part Number
ADM3202ARN-REEL7
Description
IC,LINE TRANSCEIVER,2 DRIVER,2 RCVR,SOP,16PIN,PLASTIC
Manufacturer
Analog Devices Inc
Type
Transceiverr
Datasheet
1.ADM3202ARUZ.pdf
(12 pages)
Specifications of ADM3202ARN-REEL7
Rohs Status
RoHS non-compliant
Number Of Drivers/receivers
2/2
Protocol
RS232
Voltage - Supply
3 V ~ 5.5 V
Mounting Type
Surface Mount
Package / Case
16-SOIC (3.9mm Width)
Data Rate
460Kbps
Interface Circuit Standard 1
EIA/TIA-232-E/RS-232
Number Of Receivers
2
Number Of Transmitters
2
Number Of Transceivers
1
Data Transmission Topology
Point-to-Point
Receiver Signal Type
Single-Ended
Transmitter Signal Type
Single-Ended
Single Supply Voltage (typ)
3.3V
Single Supply Voltage (min)
3V
Single Supply Voltage (max)
5.5V
Dual Supply Voltage (typ)
Not RequiredV
Dual Supply Voltage (min)
Not RequiredV
Dual Supply Voltage (max)
Not RequiredV
Supply Current
12mA
Power Supply Requirement
Single
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
16
Package Type
SOIC N
Lead Free Status / Rohs Status
Not Compliant
Other names
ADM3202ARN-REEL7
ADM3202ARNREEL7TR
ADM3202ARNREEL7TR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADM3202ARN-REEL7
Manufacturer:
ALCOR
Quantity:
40
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
PIN CONFIGURATIONS (N, RN, RU, AND RW PACKAGES)
PIN CONFIGURATIONS (RS AND RU PACKAGES)
Table 3. Pin Function Descriptions
Mnemonic
V
V+
V–
GND
C1+, C1–
C2+, C2–
Tx
Tx
Rx
Rx
EN
SD
SD
DD
NC
CC
IN
OUT
IN
OUT
Figure 4. N, RN, RU, and RW Packages Pin Configuration
Figure 6. RS and RU Packages Pin Configuration
Description
Ground Pin. Must be connected to 0 V.
are disabled.
No Connect.
Power Supply Input (3.3 V ± 0.3 V).
Internally Generated Positive Supply (+6 V nominal).
Internally Generated Negative Supply (−6 V nominal).
External Capacitor 1 is connected between these pins. A 0.1 μF capacitor is recommended but larger capacitors up to 47 μF
can be used.
External Capacitor 2 is connected between these pins. A 0.1 μF capacitor is recommended but larger capacitors up to 47 μF
can be used.
Transmitter (Driver) Inputs. These inputs accept TTL/CMOS levels.
Transmitter (Driver) Outputs. These are RS-232 signal levels (typically ±9 V).
Receiver Inputs. These inputs accept RS-232 signal levels. An internal 5 kΩ pull-down resistor to GND is connected on each input.
Receiver Outputs. These are CMOS output logic levels.
(ADM3222 only) Receiver Enable. Active low. When low, the receiver outputs are enabled. When high, they are three-stated.
(ADM3222 only) Shutdown Control. Active low. When low, the charge pump is shut down and the transmitter outputs
(ADM1385 only) Shutdown Control. When low, the charge pump is shut down and all transmitters and receivers are disabled.
(ADM1385 only) Driver Disable. When low, the charge pump is turned off and the transmitters are disabled. The receivers
remain active.
T2
R2
T2
R2
C1+
C1–
C2+
C2–
OUT
R2
C1+
C2+
C1–
C2–
OUT
OUT
V+
V–
EN
IN
V+
V–
IN
10
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
9
NC = NO CONNECT
(SSOP/TSSOP)
(Not to Scale)
(Not to Scale)
ADM3222
ADM3202
TOP VIEW
TOP VIEW
20
19
18
17
16
15
14
13
12
11
16
15
14
13
12
11
10
9
SD
V
GND
T1
R1
R1
NC
T1
T2
NC
V
GND
T1
R1
R1
T1
T2
R2
CC
CC
OUT
IN
IN
IN
OUT
OUT
IN
IN
IN
OUT
OUT
Rev. D | Page 5 of 12
Figure 5. N and RW Packages Pin Configuration
T2
Figure 7. RS Package Pin Configuration
T2
R2
ADM3202/ADM3222/ADM1385
R2
C1+
C1–
C2+
C2–
OUT
C1+
C1–
C2+
C2–
OUT
DD
NC
V+
V–
EN
V+
V–
IN
IN
10
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
NC = NO CONNECT
(Not to Scale)
(Not to Scale)
ADM3222
ADM1385
TOP VIEW
TOP VIEW
(SSOP)
18
17
16
15
14
13
12
11
10
20
19
18
17
16
15
14
13
12
11
SD
V
GND
T1
R1
R1
T1
T2
R2
SD
V
GND
T1
R1
R1
T1
T2
R2
NC
CC
CC
OUT
IN
IN
IN
OUT
OUT
OUT
IN
IN
IN
OUT
OUT