ADSP-2185MBSTZ-266 Analog Devices Inc, ADSP-2185MBSTZ-266 Datasheet - Page 9
![75mhz 16k/16k 2.5v LQFP](/photos/6/59/65915/st-100_sml.jpg)
ADSP-2185MBSTZ-266
Manufacturer Part Number
ADSP-2185MBSTZ-266
Description
75mhz 16k/16k 2.5v LQFP
Manufacturer
Analog Devices Inc
Series
ADSP-21xxr
Type
Fixed Pointr
Datasheet
1.ADSP-2185MBSTZ-266.pdf
(40 pages)
Specifications of ADSP-2185MBSTZ-266
Interface
Host Interface, Serial Port
Clock Rate
66MHz
Non-volatile Memory
External
On-chip Ram
80kB
Voltage - I/o
3.30V
Voltage - Core
2.50V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
100-LQFP
Package
100LQFP
Numeric And Arithmetic Format
Fixed-Point
Maximum Speed
66 MHz
Ram Size
80 KB
Device Million Instructions Per Second
66 MIPS
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
ADSP-2185MBSTZ266
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADSP-2185MBSTZ-266
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Interrupts
The interrupt controller allows the processor to respond to the
11 possible interrupts and reset with minimum overhead. The
ADSP-2185M provides four dedicated external interrupt input
pins: IRQ2, IRQL0, IRQL1, and IRQE (shared with the PF7:4
pins). In addition, SPORT1 may be reconfigured for IRQ0,
IRQ1, FI and FO, for a total of six external interrupts. The
ADSP-2185M also supports internal interrupts from the timer,
the byte DMA port, the two serial ports, software, and the power-
down control circuit. The interrupt levels are internally prioritized
and individually maskable (except power- down and reset). The
IRQ2, IRQ0, and IRQ1 input pins can be programmed to be
either level- or edge-sensitive. IRQL0 and IRQL1 are level-
sensitive and IRQE is edge-sensitive. The priorities and vector
addresses of all interrupts are shown in Table I.
Source Of Interrupt
Reset (or Power-Up with PUCR = 1)
Power-Down (Nonmaskable)
IRQ2
IRQL1
IRQL0
SPORT0 Transmit
SPORT0 Receive
IRQE
BDMA Interrupt
SPORT1 Transmit or IRQ1
SPORT1 Receive or IRQ0
Timer
Interrupt routines can either be nested with higher priority inter-
rupts taking precedence or processed sequentially. Interrupts
can be masked or unmasked with the IMASK register. Individual
interrupt requests are logically ANDed with the bits in IMASK;
the highest priority unmasked interrupt is then selected. The
power-down interrupt is nonmaskable.
The ADSP-2185M masks all interrupts for one instruction
cycle following the execution of an instruction that modifies the
IMASK register. This does not affect serial port autobuffering
or DMA transfers.
The interrupt control register, ICNTL, controls interrupt nest-
ing and defines the IRQ0, IRQ1, and IRQ2 external interrupts
to be either edge- or level-sensitive. The IRQE pin is an exter-
nal edge sensitive interrupt and can be forced and cleared. The
IRQL0 and IRQL1 pins are external level sensitive interrupts.
The IFC register is a write-only register used to force and clear
interrupts. On-chip stacks preserve the processor status and are
automatically maintained during interrupt handling. The stacks
are twelve levels deep to allow interrupt, loop, and subroutine
nesting. The following instructions allow global enable or disable
servicing of the interrupts (including power down), regardless
Table I. Interrupt Priority and Interrupt Vector Addresses
Interrupt Vector
Address (Hex)
0000 (Highest Priority)
002C
0004
0008
000C
0010
0014
0018
001C
0020
0024
0028 (Lowest Priority)
of the state of IMASK. Disabling the interrupts does not affect
serial port autobuffering or DMA.
ENA INTS;
DIS INTS;
When the processor is reset, interrupt servicing is enabled.
LOW POWER OPERATION
The ADSP-2185M has three low power modes that significantly
reduce the power dissipation when the device operates under
standby conditions. These modes are:
• Power-Down
• Idle
• Slow Idle
The CLKOUT pin may also be disabled to reduce external
power dissipation.
Power-Down
The ADSP-2185M processor has a low power feature that lets
the processor enter a very low-power dormant state through
hardware or software control. Following is a brief list of power-
down features. Refer to the ADSP-2100 Family User’s Manual,
“System Interface” chapter, for detailed information about the
power-down feature.
• Quick recovery from power-down. The processor begins
• Support for an externally generated TTL or CMOS processor
• Support for crystal operation includes disabling the oscillator
• Power-down is initiated by either the power-down pin (PWD)
• Context clear/save control allows the processor to continue
• The RESET pin also can be used to terminate power-down.
• Power-down acknowledge pin indicates when the processor
Idle
When the ADSP-2185M is in the Idle Mode, the processor
waits indefinitely in a low-power state until an interrupt occurs.
When an unmasked interrupt occurs, it is serviced; execution
then continues with the instruction following the IDLE instruc-
tion. In Idle mode IDMA, BDMA and autobuffer cycle steals
still occur.
executing instructions in as few as 200 CLKIN cycles.
clock. The external clock can continue running during power-
down without affecting the lowest power rating and 200 CLKIN
cycle recovery.
to save power (the processor automatically waits approximately
4096 CLKIN cycles for the crystal oscillator to start or stabi-
lize), and letting the oscillator run to allow 200 CLKIN cycle
start-up.
or the software power-down force bit. Interrupt support allows
an unlimited number of instructions to be executed before
optionally powering down. The power-down interrupt also
can be used as a nonmaskable, edge-sensitive interrupt.
where it left off or start with a clean context when leaving the
power-down state.
has entered power-down.
ADSP-2185M