ADUM4402CRWZ-RL Analog Devices Inc, ADUM4402CRWZ-RL Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADUM4402CRWZ-RL
Manufacturer Part Number
ADUM4402CRWZ-RL
Description
Quad-Ch 5kV Enhanced ESD Dig Isolator
Manufacturer
Analog Devices Inc
Series
iCoupler®r
Datasheet
1.ADUM4400ARWZ.pdf
(20 pages)
Specifications of ADUM4402CRWZ-RL
Inputs - Side 1/side 2
2/2
Number Of Channels
4
Isolation Rating
5000Vrms
Voltage - Supply
2.7 V ~ 5.5 V
Data Rate
90Mbps
Propagation Delay
27ns
Output Type
Logic
Package / Case
16-SOIC (0.300", 7.5mm Width)
Operating Temperature
-40°C ~ 105°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
APPLICATIONS INFORMATION
PC BOARD LAYOUT
The ADuM440x digital isolators require no external interface
circuitry for the logic interfaces. Power supply bypassing is
strongly recommended at the input and output supply pins
(see Figure 17). Bypass capacitors are most conveniently
connected between Pin 1 and Pin 2 for V
and Pin 16 for V
μF and 0.1 μF. The total lead length between both ends of th
capacitor and the input power supply pin should not exceed
20 mm. Bypassing between Pin 1 and Pin 8 and between Pin 9
and Pin 16 should also be considered unless the ground pair
on each package side are connected close to the package.
In applications involving high common-mode transients,
ensure that board coupling across the isolation barrier is
minimized. Furthermore, the board layout should be designed
such that any coupling that does occur equally affects all pins
on a given component side. Failure to ensure this could cause
voltage differentials between pins exceeding the Absolute
Maximum Ratings of the device, thereby leading to latch-up
or permanent damage.
SYSTEM-LEVEL ESD CONSIDERATIONS AND
ENHANCEMENTS
System-level ESD reliability (for example, per IEC 61000-4-x) is
highly dependent on system design, which varies widely by
application. The ADuM440x incorporate many enhancements
to make ESD reliability less dependent on system design. The
enhancements include
• ESD protection cells added to all input/output interfaces.
• Key metal trace resistances reduced using wider geometry
• The SCR effect, inherent in CMOS devices, minimized by
• Areas of high electric field concentration eliminated using
• Supply pin overvoltage prevented with larger ESD clamps
and paralleling of lines with vias.
using guarding and isolation techniques between PMOS
and NMOS devices.
45° corners on metal traces.
between each supply pin and its respective ground.
V
V
NC/V
IC/
ID/
GND
GND
V
Figure 17. Recommended Printed Circuit Board Layout
V
V
DD1
V
V
OC
OD
E1
IA
IB
1
1
DD2
. The capacitor value should be between 0.01
DD1
and between P
V
GND
V
V
V
V
V
GND
DD2
OA
OB
OC/
OD/
E2
V
V
2
2
IC
ID
in 15
e
Rev. 0 | Page 15 of 20
While the ADuM440x improve system-level ESD reliability,
they are no substitute for a robust system-level design. See the
AN-793 Application Note, ESD/Latch-Up Considerations with
iCoupler Isolation Products, for detailed recommendations on
board layout and system-level design.
PROPAGATION DELAY-RELATED PARAMETERS
Propagation delay is a parameter that describes the length of
time for a logic signal to propagate through a component. The
propagation delay to a logic low output can differ from the
propagation delay to logic high.
Pulse width distortion is the maximum difference between
these two propagation delay values and is an indication of how
accurately the input signal’s timing is preserved.
Channel-to-channel matching refers to the maximum amount
the propagation delay differs among channels within a single
ADuM440x component.
Propagation delay skew refers to the maximum amount the
propagation delay differs among multiple ADuM440x
components operated under the same conditions.
DC CORRECTNESS AND MAGNETIC FIELD
IMMUNITY
Positive and negative logic transitions at the isolator input cause
narrow (~1 ns) pulses to be sent via the transformer to the
decoder. The decoder is bistable and is therefore either set or
reset by the pulses, indicating input logic transitions. In the
absence of logic transitions at the input for more than ~1 μs, a
periodic set of refresh pulses indicative of the correct input state
are sent to ensure dc correctness at the output. If the decoder
receives no internal pulses for more than approximately 5 μs,
the input side is assumed to be without power or nonfunctional;
in which case, the isolator output is forced to a default state
(see Table 20) by the watchdog timer circuit.
The limitation on the ADuM440x magnetic field immunity is
set by the condition in which induced voltage in the trans-
former’s receiving coil is large enough to either falsely set or
reset the decoder. The following analysis defines the conditions
under which this can occur. The 3 V operating condition of the
ADuM440x is examined because it represents the most
susceptible mode of operation.
INPUT (V
OUTPUT (V
Ix
)
Ox
ADuM4400/ADuM4401/ADuM4402
)
Figure 18. Propagation Delay Parameters
t
PLH
t
PHL
50%
50%