ADUM5202ARWZ-RL Analog Devices Inc, ADUM5202ARWZ-RL Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADUM5202ARWZ-RL
Manufacturer Part Number
ADUM5202ARWZ-RL
Description
DUAL-CHANNEL ISOLATOR W/INTEGRADED DC/DC
Manufacturer
Analog Devices Inc
Series
IsoPower®, iCoupler®r
Datasheet
1.ADUM5200CRWZ.pdf
(24 pages)
Specifications of ADUM5202ARWZ-RL
Inputs - Side 1/side 2
0/2
Number Of Channels
2
Isolation Rating
2500Vrms
Voltage - Supply
3.3V, 5V
Data Rate
1Mbps
Propagation Delay
55ns
Output Type
Logic
Package / Case
16-SOIC (0.300", 7.5mm Width)
Operating Temperature
-40°C ~ 105°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
ADuM5200/ADuM5201/ADuM5202
Parameter
AC SPECIFICATIONS
1
2
3
4
5
6
7
The contributions of supply current values for all four channels are combined at identical data rates.
V
proportional to the data rate. Additional supply current associated with an individual channel operating at a given data rate may be calculated as described in the
Power Consumption section. The dynamic I/O channel load must be treated as an external load and be included in the V
The power demands of the quiescent operation of the data channels cannot be separated from the power supply section. Efficiency includes the quiescent power
consumed by the I/O channels as part of its internal power consumption.
I
maximum dynamic load conditions. Treat resistive loads on the outputs separately from the dynamic load.
This current is available for driving external loads at the V
representing the maximum dynamic load conditions. Refer to the Power Consumption section for the calculation of available current at less than the maximum data rate.
Undervoltage lockout (UVLO) holds the outputs in a low state if the corresponding input or output power supply is below the referenced threshold. Hysteresis is built
into the detection threshold to prevent oscillations and noise sensitivity.
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
DD1(D)
ISO
ADuM520xARWZ
ADuM520xCRWZ
For All Models
supply current is available for external use when all data rates are below 2 Mbps. At data rates above 2 Mbps data I/O channels draw additional current
Minimum Pulse Width
Minimum Pulse Width
Channel-to-Channel Matching,
Channel-to-Channel Matching,
Output Rise/Fall Time (10% to 90%)
Common-Mode Transient Immunity
Common-Mode Transient Immunity
Refresh Rate
Maximum Data Rate
Propagation Delay
Pulse Width Distortion, |t
Propagation Delay Skew
Channel-to-Channel Matching
Maximum Data Rate
Propagation Delay
Pulse Width Distortion, |t
Propagation Delay Skew
is the typical input supply current with all channels simultaneously driven at a maximum data rate of 25 Mbps with the full capacitive load representing the
Codirectional Channels
Opposing-Directional Channels
at Logic High Output
at Logic Low Output
Change vs. Temperature
7
7
PLH
PLH
− t
− t
PHL
PHL
|
|
Symbol
PW
t
PWD
t
t
PW
t
PWD
t
t
t
t
|CM
|CM
f
PHL
PSK
PSKCD
PHL
PSK
PSKCD
PSKOD
R
r
/t
F
, t
, t
ISO
H
L
|
, t
|
PLH
PLH
pin. All channels are simultaneously driven at a maximum data rate of 25 Mbps with the full capacitive load
PSKOD
Min
1
25
25
25
Rev. 0 | Page 6 of 24
Typ
60
45
5
2.5
35
35
1.0
Max
1000
100
40
50
50
40
60
6
45
6
15
Unit
ns
Mbps
ns
ns
ns
ns
ns
Mbps
ns
ns
ps/°C
ns
ns
ns
ns
kV/μs
kV/μs
Mbps
ISO
Test Conditions
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
V
transient magnitude = 800 V
V
transient magnitude = 800 V
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Ix
Ix
power budget.
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= V
= 0 V, V = 1000 V,
DD
or V
ISO
, V
CM
= 1000 V,