ADUM5400CRWZ-RL Analog Devices Inc, ADUM5400CRWZ-RL Datasheet - Page 4

• Manufacturer Part Number: ADUM5400CRWZ-RL
• Description: QUAD-CHANNEL DIGITAL ISOLATORS
• Manufacturer: Analog Devices Inc
• Series: IsoPower®, iCoupler®r

Specifications of ADUM5400CRWZ-RL

• Inputs - Side 1/side 2: 4/0
• Number Of Channels: 4
• Isolation Rating: 2500Vrms
• Voltage - Supply: 3.35V, 4.1V, 5V
• Data Rate: 25Mbps
• Propagation Delay: 45ns
• Output Type: Logic
• Package / Case: 16-SOIC (0.300", 7.5mm Width)
• Operating Temperature: -40°C ~ 105°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADUM540XEBZ - BOARD EVAL FOR ADUM540x
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADuM5400
Parameter
1
2
3
4
5
6
The contributions of supply current values for all four channels are combined at identical data rates.
The V
proportional to the data rate. Additional supply current associated with an individual channel operating at a given data rate can be calculated as described in the
Power Consumption
The power demands of the quiescent operation of the data channels cannot be separated from the power supply section. Efficiency includes the quiescent power
consumed by the I/O channels as part of the internal power consumption.
This current is available for driving external loads at the V
representing the maximum dynamic load conditions. Refer to the Power C
Undervoltage lockout (UVLO) holds the outputs in a low state if the corresponding input or output power supply is below the referenced threshold. Hysteresis is built
into the detection threshold to prevent oscillations and noise sensitivity.
The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed.
ADuM5400CRWZ
For All Models
Minimum Pulse Width
Maximum Data Rate
Propagation Delay
Pulse Width Distortion, |t
Propagation Delay Skew
Channel-to-Channel Matching,
Channel-to-Channel Matching,
Output Rise/Fall Time (10% to 90%)
Common-Mode Transient Immunity
Common-Mode Transient Immunity
Refresh Rate
ISO
Change vs. Temperature
Codirectional Channels
Opposing Directional Channels
at Logic High Output
at Logic Low Output
supply current is available for external use when all data rates are below 2 Mbps. At data rates above 2 Mbps, the data I/O channels draw additional current
section. The dynamic I/O channel load must be treated as an external load and included in the V
6
PLH
− t
PHL
|
Symbol
PW
t
PWD
t
t
t
t
|CM
|CM
f
r
PHL
PSK
PSKCD
PSKOD
R
/t
, t
F
H
L
|
ISO
|
PLH
pin. All channels are simultaneously driven at a maximum data rate of 25 Mbps with full capacitive load
Min
25
25
25
Rev. 0 | Page 4 of 16
onsumption
Typ
45
5
2.5
35
35
1.0
section for calculation of available current at less than the maximum data rate.
Max
40
60
6
15
6
15
Unit
ns
Mbps
ns
ns
ps/°C
ns
ns
ns
ns
kV/μs
kV/μs
Mbps
ISO
power budget.
Test Conditions/Comments
C
C
C
C
C
C
C
C
C
V
transient magnitude = 800 V
V
transient magnitude = 800 V
L
L
L
L
L
L
L
L
L
Ix
Ix
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= 15 pF, CMOS signal levels
= V
= 0 V, V
DD
or V
CM
ISO
= 1000 V,
, V
CM
= 1000 V,