ADV7180KCP32Z Analog Devices Inc, ADV7180KCP32Z Datasheet - Page 37
![no-image](/images/manufacturer_photos/0/0/57/analog_devices_inc_sml.jpg)
ADV7180KCP32Z
Manufacturer Part Number
ADV7180KCP32Z
Description
10-bit 4x Oversampling SDTV Decoder
Manufacturer
Analog Devices Inc
Type
Video Decoderr
Datasheet
1.ADV7180BSTZ.pdf
(116 pages)
Specifications of ADV7180KCP32Z
Design Resources
Low Cost Differential Video Receiver Using ADA4851 Amplifier and ADV7180 Video Decoder (CN0060) Low Cost Video Multiplexer for Video Switching Using ADA4853-2 Op Amp with Disable Function (CN0076)
Applications
Digital Cameras, Mobile Phones, Portable Video
Voltage - Supply, Analog
1.71 V ~ 1.89 V
Voltage - Supply, Digital
1.65 V ~ 2 V
Mounting Type
Surface Mount
Package / Case
32-LFCSP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADV7180KCP32Z
Manufacturer:
SEMTECH
Quantity:
13 400
Part Number:
ADV7180KCP32Z
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
ADV7180KCP32Z-RL
Manufacturer:
ANALOGDEVICES
Quantity:
20 000
CAGT[1:0], Chroma Automatic Gain Timing,
Address 0x2D[7:6]
The chroma automatic gain timing register allows the user to
influence the tracking speed of the chroma automatic gain
control. This register has an effect only if the CAGC[1:0]
register is set to 10 (automatic gain).
Table 45. CAGT Function
CAGT[1:0]
00
01
10
11 (default)
CG[11:0], Chroma Gain, Address 0x2D[3:0],
Address 0x2E[7:0]; CMG[11:0], Chroma Manual Gain,
Address 0x2D[3:0], Address 0x2E[7:0]
Chroma gain[11:0] is a dual-function register. If written to, a
desired manual chroma gain can be programmed. This gain
becomes active if the CAGC[1:0] function is switched to
manual fixed gain. See Equation 2 for calculating a desired gain.
If read back, this register returns the current gain value.
Depending on the setting in the CAGC[1:0] bits, this is either:
•
•
Table 46. CG/CMG Function
CG[11:0]/CMG[11:0]
CMG[11:0]
CG[11:0]
where ChromaCalibrationFactor is a decimal value between 0
and 4095.
Calculation of the Luma Calibration Factor
1.
2.
3.
The chroma manual gain value (CAGC[1:0] set to chroma
manual gain mode).
The chroma automatic gain value (CAGC[1:0] set to any of
the automatic modes).
Chroma_Gain
Apply a CVBS signal with the color bars/SMPTE bars test
pattern content directly to the measurement equipment.
Ensure correct termination of 75 Ω on the measurement
equipment. Measure chroma output levels.
Reconnect the source to the CVBS input of the ADV7180
system that has a backend gain of 1. Repeat the
measurement of chroma levels.
≅
ChromaCali
Read/Write
Write
Read
Description
Slow (TC = 2 sec)
Medium (TC = 1 sec)
Reserved
Adaptive
CMG
[
11
brationFac
:
] 0
Description
Manual gain for chroma
path
Currently active gain
decimal
tor
Rev. F | Page 37 of 116
(2)
4.
This value, in decimal, is the chroma calibration factor.
CKE, Color Kill Enable, Address 0x2B[6]
The color kill enable bit allows the optional color kill function
to be switched on or off.
For QAM-based video standards (PAL and NTSC) as well as
FM-based systems (SECAM), the threshold for the color kill
decision is selectable via the CKILLTHR[2:0] bits.
If color kill is enabled and the color carrier of the incoming
video signal is less than the threshold for 128 consecutive video
lines, color processing is switched off (black and white output).
To switch the color processing back on, another 128 consecutive
lines with a color burst greater than the threshold are required.
The color kill option works only for input signals with a modulated
chroma part. For component input (YPrPb), there is no color kill.
Setting CKE to 0 disables color kill.
Setting CKE to 1 (default) enables color kill.
CKILLTHR[2:0], Color Kill Threshold, Address 0x3D[6:4]
The CKILLTHR[2:0] bits allow the user to select a threshold for
the color kill function. The threshold applies only to QAM-based
(NTSC and PAL) or FM-modulated (SECAM) video standards.
To enable the color kill function, the CKE bit must be set. For
Setting 000, Setting 001, Setting 010, and Setting 011, chroma
demodulation inside the ADV7180 may not work satisfactorily
for poor input video signals.
Table 47. CKILLTHR Function
CKILLTHR[2:0]
000
001
010
011 (default)
100
101
110
111
Turn off the Chroma AGC and manually change the
Chroma Gain Control Register CMG[11:0] until the
chroma level matches that measured directly from the
source.
SECAM
No color kill
Kill at <5%
Kill at <7%
Kill at <8%
Kill at <9.5%
Kill at <15%
Kill at <32%
Reserved for Analog Devices internal use only;
do not select
Description
NTSC, PAL
Kill at <0.5%
Kill at <1.5%
Kill at <2.5%
Kill at <4%
Kill at <8.5%
Kill at <16%
Kill at <32%
ADV7180