DSPIC33FJ32GS406-I/MR Microchip Technology, DSPIC33FJ32GS406-I/MR Datasheet
DSPIC33FJ32GS406-I/MR
Specifications of DSPIC33FJ32GS406-I/MR
Related parts for DSPIC33FJ32GS406-I/MR
DSPIC33FJ32GS406-I/MR Summary of contents
Page 1
... Table 1. The silicon issues are summarized in Table 2. The errata described in this document will be addressed in future revisions of the dsPIC33FJ32GS406/606/608/ 610 and dsPIC33FJ64GS406/606/608/610 silicon. Note: This document summarizes all silicon errata issues from all revisions of silicon, previous as well as current. Only the issues indicated in the last column of ...
Page 2
... TABLE 2: SILICON ISSUE SUMMARY Item Module Feature Number ECAN WAKIF bit 1. Reserved — 2. SPI ASS1 Pin 3. JTAG Boundary Scan 4. PWM Secondary 5. Master Time Base Synchronization Interrupts Exit from Doze 6. Mode on Interrupt ADC Current 7. Consumption in Sleep Mode PWM External Period 8 ...
Page 3
... Silicon Errata Issues Note: This document summarizes all silicon errata issues from all revisions of silicon, previous as well as current. The shaded column in the “Affected Silicon Revisions” table included in each issue indicates that the issue applies to the most current revision of silicon (A0) ...
Page 4
... PWM period when the selected reset signal is asserted during the OFF time of the PWM. If the reset signal is asserted during the PWM ON time, then the reset signal must be ignored. However, on the dsPIC33FJ32GS406/606/608/ 610 and devices, the reset signal is not ignored at the end of the PWM ON time ...
Page 5
... Module: High Speed PWM The PENH and PENL bits in the IOCONx register are used to assign ownership of the pins to either the PWM module or the GPIO module. The correct procedure to configure the PWM module is to first assign pin ownership to the PWM module and then enabling it using the PTEN bit in the PTCON register ...
Page 6
... Module: ECAN The ERRIF status flag (CiINTF<5>) does not get set when a CAN error condition occurs. However, the corresponding CiIF interrupt flag will get set on a CAN error condition, and an interrupt will be correctly generated if enabled. Work around Do not inspect the state of the ERRIF bit to deter- mine if a CAN error interrupt has occurred ...
Page 7
... Data Sheet Clarifications The following typographic corrections and clarifications are to be noted for the latest version of the device data sheet (DS70591C): Note: Corrections are shown in bold. Where possible, the original bold text formatting has been removed for clarity. ...
Page 8
... APPENDIX A: REVISION HISTORY Rev A Document (10/2009) Initial release of this document; issued for revision A0. Includes silicon issues 1 (ECAN), 2 (SPI), 3 (SPI) 4 (JTAG), 5 (PWM) and 6 (Interrupts). Rev B Document (6/2010) Removed silicon issue 2 (SPI) and marked its location as reserved. Updated the work around in silicon issue 5 (PWM). ...
Page 9
... PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 10
... Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-6578-300 Fax: 886-3-6578-370 Taiwan - Kaohsiung Tel: 886-7-213-7830 Fax: 886-7-330-9305 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2010 Microchip Technology Inc. 08/04/10 ...