KSZ8841-32MVL Micrel Inc, KSZ8841-32MVL Datasheet - Page 35
![Single Ethernet Port + Generic (32-bit) Bus Interface( )](/photos/6/81/68160/ksz8841-32mvl_sml.jpg)
KSZ8841-32MVL
Manufacturer Part Number
KSZ8841-32MVL
Description
Single Ethernet Port + Generic (32-bit) Bus Interface( )
Manufacturer
Micrel Inc
Specifications of KSZ8841-32MVL
Controller Type
Ethernet Controller, MAC
Interface
Bus
Voltage - Supply
3.1 V ~ 3.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
128-LQFP
Operating Supply Voltage (typ)
3.3V
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
128
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
576-1632 - BOARD EVALUATION KSZ8841-16MVL
Current - Supply
-
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Other names
576-2116
KSZ8841-32MVL
KSZ8841-32MVL
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Regardless of whether the transfer is synchronous or asynchronous, if the address latch is required, use the rising edge of
ADSN to latch the incoming signals A[15:1], AEN, BE3N, BE2N, BE1N, and BE0N.
Note: If the local device decoder is used in either synchronous or asynchronous transfers, LDEVN will be asserted to
indicate that the KSZ8841M is successfully targeted. The signal LDEVN is a combinatorial decode of AEN and A[15:4].
Asynchronous Interface
For asynchronous transfers, the asynchronous dedicated signals RDN (for read) or WRN (for write) toggle, but the
synchronous dedicated signals CYCLEN, SWR, and RDYRTNN are de-asserted and stay at the same logic level
throughout the entire asynchronous transfer.
There is no data burst support for asynchronous transfer. All asynchronous transfers are single-data transfers. The BIU,
however, provides flexible asynchronous interfacing to communicate with various applications and architectures. Three
major ways of interfacing with the system (host) are.
1. Interfacing with the system/host relying on local device decoding and having stable address throughout the whole
Interfacing with the system/host relying on local device decoding but not having stable address throughout the entire
transfer: The typical example for this application is EISA-like bus (non-burst) interface as shown in the Figure 14. This
type of interface requires ADSN to latch the address on the rising edge. The BIU decodes latched A[15:4] and qualifies
with AEN to determine if the KSZ8841M device is the intended target. The data transfer is the same as the first case.
Interfacing with the system/host relying on central decoding (KSZ8841-32MQL only).
The typical example for this application is for an embedded processor having a central decoder on the system board or
within the processor. Connecting the chip select (CS) from system/host to DATACSN bypasses the local device decoder.
When the DATACSN is asserted, it only allows access to the Data Register in 32 bits and BE3N, BE2N, BE1N, and BE0N
are ignored as shown in the Figure 15. No other registers can be accessed by asserting DATACSN. The data transfer is
the same as in the first case. Independent of the type of asynchronous interface used. To insert a wait state, the BIU will
assert ARDY to prolong the cycle.
October 2007
Micrel, Inc.
transfer: The typical example for this application is ISA-like bus interface using latched address signals as shown
in Figure 13. No additional address latch is required, therefore ADSN should be connected Low. The BIU decodes
A[15:4] and qualifies with AEN (Address Enable) to determine if the KSZ8841M device is the intended target. The
host utilizes the rising edge of RDN to latch read data and the BIU will use rising edge of WRN to latch write data.
Signal
BCLK
Asynchronous Transfer Signals
RDN
WRN
ARDY
Note 1: I = Input. O = Output. I/O = Bi-directional.
Type
I
I
I
O
(1)
Table 2. Bus Interface Unit Signal Grouping
Function
For burst access: exactly like EXRDY signal in EISA to insert wait states. Note that
the wait states are inserted by system logic (memory) not by KSZ8841M.
Bus Clock
Asynchronous Read
Asynchronous Write
Asynchronous Ready
This signal is asserted (Low) to insert wait states.
35
KSZ8841-16/32 MQL/MVL/MBL
M9999-102207-1.6