KSZ8842-32MVL Micrel Inc, KSZ8842-32MVL Datasheet - Page 16
![no-image](/images/manufacturer_photos/0/4/434/micrel_inc_sml.jpg)
KSZ8842-32MVL
Manufacturer Part Number
KSZ8842-32MVL
Description
2-Port Ethernet Switch/Repeater + Generic (32-bit) Bus Interface( )
Manufacturer
Micrel Inc
Specifications of KSZ8842-32MVL
Controller Type
Ethernet Switch Controller
Interface
PCI
Voltage - Supply
3.1 V ~ 3.5 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
128-LQFP
Number Of Primary Switch Ports
2
Internal Memory Buffer Size
32
Operating Supply Voltage (typ)
3.3V
Fiber Support
Yes
Integrated Led Drivers
Yes
Phy/transceiver Interface
MII
Power Supply Type
Analog/Digital
Data Rate (typ)
10/100Mbps
Vlan Support
Yes
Operating Temperature (max)
70C
Operating Temperature (min)
0C
Pin Count
128
Mounting
Surface Mount
Jtag Support
No
Operating Supply Voltage (max)
3.5V
Operating Supply Voltage (min)
3.1V
Operating Temperature Classification
Commercial
Data Rate
100Mbps
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
576-1635 - BOARD EVALUATION KSZ8842-16MVL
Current - Supply
-
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
KSZ8842-32MVLI
Manufacturer:
Micrel
Quantity:
915
Micrel, Inc.
October 2007
Pin Number
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
Pin Name
VDDAP
VDDIO
AGND
AGND
AGND
DGND
DGND
VDDC
VDDA
RSTN
TXM2
BE1N
BE0N
TXP2
ISET
A15
A14
A13
A12
A11
A10
NC
NC
NC
NC
NC
X1
X2
A9
A8
A7
A6
A5
A4
A3
A2
A1
Type
Gnd
Gnd
Gnd
Gnd
Gnd
I/O
I/O
Ipu
Ipu
Ipu
P
O
P
O
P
P
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Pin Function
Port 2 physical transmit (MDI) or receive (MDIX) signal (- differential)
Port 2 physical transmit (MDI) or receive (MDIX) signal (+ differential)
1.2 analog V
bead and capacitor.
Analog ground
No connect
No connect
Set physical transmits output current.
Pull-down this pin with a 3.01K 1% resistor to ground.
Analog ground
1.2V analog V
external Ferrite bead and capacitor.
Analog ground
25MHz crystal or oscillator clock connection.
Pins (X1, X2) connect to a crystal. If an oscillator is used, X1 connects to a 3.3V
tolerant oscillator and X2 is a no connect.
Note: Clock requirement is ± 50ppm for either crystal or oscillator.
Hardware reset pin (active Low). This reset input is required minimum of 10ms
low after stable supply voltage 3.3V.
Address 15
Address 14
Address 13
Address 12
Address 11
Address 10
Address 9
Address 8
Address 7
Address 6
Digital IO ground
3.3V digital V
Address 5
Address 4
Address 3
Address 2
Address 1
No Connect
No Connect
Byte Enable 1 Not, Active low for Data byte 1 enable (don’t care in 8-bit bus
mode).
Byte Enable 0 Not, Active low for Data byte 0 enable (there is an internal inverter
enabled and connected to the BE1N for 8-bit bus mode).
No Connect
Digital core ground
1.2V digital core V
Ferrite bead and capacitor.
DD
DDIO
DD
input power supply from VDDCO (pin24) through external Ferrite
for PLL input power supply from VDDCO (pin24) through
input power supply for IO with well decoupling capacitors.
16
DD
input power supply from VDDCO (pin24) through external
KSZ8842-16/32 MQL/MVL/MVLI/MBL
M9999-102207-1.9