CYII5SC1300AB-QDC Cypress Semiconductor Corp, CYII5SC1300AB-QDC Datasheet - Page 22

• Manufacturer Part Number: CYII5SC1300AB-QDC
• Description: SENSOR IMAGE COLOR CMOS 84-LCC
• Manufacturer: Cypress Semiconductor Corp
• Type: CMOS Imagingr

Specifications of CYII5SC1300AB-QDC

• Pixel Size: 6.7µm x 6.7µm
• Active Pixel Array: 1280H x 1024V
• Frames Per Second: 27
• Voltage - Supply: 3 V ~ 4.5 V
• Package / Case: 84-LCC
• Sensor Image Color Type: Color
• Sensor Image Size Range: >= 480,000Pixels
• Sensor Image Size: 1280x1024Pixels
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Temp Range: 0C to 65C
• Package Type: CLCC
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 84
• Package: 84CLCC
• Image Size: 1280x1024 Pixels
• Color Sensing: Color
• Operating Temperature: 0 to 65 °C
• Operating Supply Voltage: 3 to 3.6 V
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

when the pixel counter reaches the value loaded in the
NROF_PIXELS register (after a complete row read out).
T
value loaded in the NROF_LINES register and stays high for one
line period (until the next falling edge of Y-CLOCK).
On Y_START the left Y-shift-register of the image core is loaded
with the YL-pointer that is loaded in to register YL_REG.
Pixel Output
The pixel signal at the PXL_OUT1 output becomes valid after
five SYS_CLOCK cycles when the internal X_SYNC (= start of
PIXEL_VALID output or external X_LOAD pulse) pulse is
asserted. (See
T
T
T
(see
Document #: 38-05710 Rev. *G
3
1
2
3
—LAST_LINE goes high when the line counter reaches the
—Row blanking time
—5 SYS_CLOCK cycles.
—Time for new X-pointer position upload in X_REG register
Windowing in X-direction
Figure
24).
(seeTable 21
on page 24 for more details).
).
Figure 23. Global Shutter: Pixel Read Out
Figure 24. Pixel Output
Advanced Operation:
It was observed during characterization of the IBIS5-B-1300
image sensor that there are column non-uniformities in the
image in syncronous shutter mode, when the Y-readout pointer
is still selecting a line during the global reset for the next frame.
To avoid this problem, an advanced timing has been generated
for the syncronous shutter mode. Please look into application
note - FAQ for IBIS5-1300 image sensor (AN6004 - question 12)
for more information. The application note discusses the cause
and corrective action for this problem.
Table 21. Row Blanking Time as Function of X-Sequencer
Granularity
Granularity
N
x 16
x 32
GRAN
x 4
x 8
= 35 x N
1120 x T
560 x T
140 x T
280 x T
GRAN
SYS_CLOCK
SYS_CLOCK
SYS_CLOCK
SYS_CLOCK
T
1
(µs)
x T
SYS_CLOCK
CYII5SM1300AB
= 14.0
= 3.5
= 7.0
= 28.0
GRAN_X_SEQ
Page 22 of 34
MSB/LSB
00
01
10
11