TISP4395L3AJR Bourns Inc., TISP4395L3AJR Datasheet - Page 10
![Sidacs](/photos/16/7/160746/tisp40_sml.jpg)
TISP4395L3AJR
Manufacturer Part Number
TISP4395L3AJR
Description
Sidacs
Manufacturer
Bourns Inc.
Datasheet
1.TISP4015L1BJR-S.pdf
(11 pages)
Specifications of TISP4395L3AJR
Mounting Style
SMD/SMT
Package / Case
DO-214AC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
TISP4395L3AJR-S
Manufacturer:
BOURNS
Quantity:
240 000
For an HDSL d.c. feed voltage of 180 V or less and operation down to an ambient of -25 °C, the following Th1, Th2, Th3 and Th4 protectors
are suitable: TISP4250M3 or TISP4250H3, TISP3250H3 (combines Th1 and Th2 or Th3 and Th4) and TISP7250H3 (combines Th1, Th2 and
Th7 or Th3, Th4 and Th8). Possible overcurrent protection components are covered in the 2-wire digital systems clause.
For ISDN interfaces powered with ±40 V (ETSI, ETS 300 012 1992) the following Th1, Th2, Th3 and Th4 protectors are suitable: TISP4070M3
or TISP4070H3 or TISP4070L3, TISP3070F3 or TISP3070H3 (combines Th1 and Th2 or Th3 and Th4) and TISP7070F3 or TISP7070H3
(combines Th1, Th2 and Th7 or Th3, Th4 and Th8). At the terminating adaptor, the Th7 and Th8 protectors do not “see” the d.c. feed voltage
and should be selected to not clip the maximum signal level. Generally, the TISP40xxL1 series will be suitable.
Internal ISDN lines are not exposed to high stress levels and the chances of a.c. power intrusion are low (ETSI EN 300 386-2 1997).
Accordingly, the equipment port protection needs are at a lower level than ports connected to outside lines.
Using the existing house telephone wiring, home phone networking systems place the local network traffic in a high band above the POTS and
ADSL (Asymmetrical Digital Subscriber Line) spectrum. Local network rates are 1 Mbps or more. To reject noise and harmonics, an in-line
protection and 5 MHz to 10 MHz bandpass filter module is used for the equipment. These modules are available from magnetic component
manufacturers (e.g. Bel Fuse Inc.) A typical circuit for the telephone line magnetics module is shown in Figure 13. Transformer T1 isolates the
equipment from the house wiring. The isolated winding output is voltage limited by a very low-voltage protector, Th1. With a differential voltage
of about 12 V peak to peak, the TISP4015L1 could be used for Th1. After filtering, connection is made to the differential transceiver of the
processing IC.
4-Wire Digital Systems (Continued)
Home Phone Networking
Th5
Th 6
SIGNAL
SIGNAL
TISP40xxL1AJ/BJ VLV Overvoltage Protectors
DC FEED
T1
T2
Figure 13. Home Phone Networking Isolation/filter/protection Circuit
HRTRX+
HRTRX-
AI4XAP
Th2
Th 3
Th1
Th4
TRANSFORMER COUPLED FOUR-WIRE INTERFACE
PROTECTION
PROTECTION
CURRENT
CURRENT
Figure 12. 4-Wire System
OVER-
OVER-
FILTER
LINE 1
LINE 2
PROTECTION
Th1
PROTECTION
PROTECTION
CURRENT
CURRENT
OVER-
OVER-
Customers should verify actual device performance in their specific applications.
T1
C1
Th7
Th8
Specifications are subject to change without notice.
TIP
RING
AUGUST 1999 - REVISED JANUARY 2007
DC SUPPLY
T3
T4
SIGNAL
SIGNAL
AI4XAM
Th10
Th 9