LT3013MPFE Linear Technology, LT3013MPFE Datasheet - Page 4

• Manufacturer Part Number: LT3013MPFE
• Description: SP-LINREG, 80Vin, 250mA, LDO W/ PWRGD In TSSOP
• Manufacturer: Linear Technology

LT3013
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: The LT3013 is tested and specifi ed for these conditions with the
ADJ pin connected to the OUT pin.
Note 3: Operating conditions are limited by maximum junction
temperature. The regulated output voltage specifi cation will not apply
for all possible combinations of input voltage and output current. When
operating at maximum input voltage, the output current range must be
limited. When operating at maximum output current, the input voltage
range must be limited.
Note 4: To satisfy requirements for minimum input voltage, the LT3013 is
tested and specifi ed for these conditions with an external resistor divider
(249k bottom, 649k top) for an output voltage of 4.5V. The external
resistor divider will add a 5μA DC load on the output.
Note 5: Dropout voltage is the minimum input to output voltage differential
needed to maintain regulation at a specifi ed output current. In dropout, the
output voltage will be equal to (V
Note 6: GND pin current is tested with V
load. This means the device is tested while operating close to its dropout
region. This is the worst-case GND pin current. The GND pin current will
decrease slightly at higher input voltages.
ELECTRICAL CHARACTERISTICS
The
4
PARAMETER
Dropout Voltage
V
GND Pin Current
V
(Notes 4, 6)
Output Voltage Noise
ADJ Pin Bias Current
Shutdown Threshold
SHDN Pin Current (Note 8)
Quiescent Current in Shutdown
PWRGD Trip Point
PWRGD Trip Point Hysteresis
PWRGD Output Low Voltage
C
C
Ripple Rejection
Current Limit
Reverse Output Current (Note 9)
IN
IN
T
T
Pin Charging Current
Pin Voltage Differential
= V
= 4.75V
l
denotes the specifi cations which apply over the –40°C to 140°C operating temperature range, otherwise specifi cations are at T
OUT(NOMINAL)
(Notes 4, 5)
IN
– V
DROPOUT
CONDITIONS
I
I
I
I
I
I
I
I
I
C
(Note 7)
V
V
V
V
V
% of Nominal Output Voltage, Output Rising
% of Nominal Output Voltage
I
V
V
V
V
V
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
PWRGD
IN
OUT
OUT
OUT
SHDN
SHDN
IN
CT(PWRGD High)
IN
IN
IN
OUT
= 4.75V and a current source
= 6V, V
= 7V(Avg), V
= 7V, V
= 4.75V, ΔV
= 10μF, I
= Off to On
= On to Off
= 1.24V, V
= 10mA
= 10mA
= 50mA
= 50mA
= 200mA
= 200mA
= 0mA
= 100mA
= 200mA
= 0V
= 6V
).
= 50μA
SHDN
OUT
LOAD
= 0V
OUT
IN
– V
= 0V
RIPPLE
< 1.24V (Note 2)
= 200mA, BW = 10Hz to 100kHz
= –0.1V (Note 2)
CT(PWRGD Low)
= 0.5V
(LT3013H)
P-P
, f
RIPPLE
Note 7: ADJ pin bias current fl ows into the ADJ pin.
Note 8: SHDN pin current fl ows out of the SHDN pin.
Note 9: Reverse output current is tested with the IN pin grounded and the
OUT pin forced to the rated output voltage. This current fl ows into the OUT
pin and out the GND pin.
Note 10: The LT3013E is guaranteed to meet performance specifi cations
from 0°C to 125°C operating junction temperature. Specifi cations over
the –40°C to 125°C operating junction temperature range are assured by
design, characterization and correlation with statistical process controls.
The LT3013H is tested to the LT3013H Electrical Characteristics table at
140°C operating junction temperature. High junction temperatures degrade
operating lifetimes. Operating lifetime is derated at junction temperatures
greater than 125°C. The LT3013MP is 100% tested and guaranteed over
the –55°C to 125°C operating junction temperature range.
Note 11: This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed 125°C (LT3013E, LT3013MP) or 140°C (LT3013H)
when overtemperature protection is active. Continuous operation above
the specifi ed maximum operating junction temperature may impair device
reliability.
= 120Hz, I
LOAD
= 200mA
l
l
l
l
l
l
l
l
l
l
MIN
200
0.3
85
65
TYP
160
250
360
100
140
400
1.3
0.8
0.3
0.1
1.1
3.0
1.6
65
30
90
75
12
3
7
1
MAX
230
320
340
450
490
630
130
100
250
18
95
25
2
2
1
5
6
J
= 25°C.
UNITS
μV
3013fe
RMS
mV
mV
mV
mV
mV
mV
mA
mA
mV
mA
mA
μA
nA
μA
μA
μA
μA
dB
μA
%
%
V
V
V