LTC4215IGN#TR Linear Technology, LTC4215IGN#TR Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LTC4215IGN#TR
Manufacturer Part Number
LTC4215IGN#TR
Description
IC,Power Control/Management,CMOS,SSOP,16PIN,PLASTIC
Manufacturer
Linear Technology
Datasheet
1.LTC4215IGNTR.pdf
(28 pages)
Specifications of LTC4215IGN#TR
Linear Misc Type
Positive Low Voltage
Family Name
LTC4215
Package Type
SSOP N
Operating Supply Voltage (min)
2.9V
Operating Supply Voltage (max)
15V
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Product Depth (mm)
3.99mm
Product Height (mm)
1.5mm
Mounting
Surface Mount
Pin Count
16
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
PIN FUNCTIONS
SCL: Serial Bus Clock Input. Data at the SDA pin is shifted
in or out on rising edges of SCL. This is a high impedance
pin that is generally driven by an open-collector output
from a master controller. An external pull-up resistor or
current source is required.
SDAO (QFN Package): Serial Bus Data Output. Open-drain
output for sending data back to the master controller or
acknowledging a write operation. Normally tied to SDAI
to form the SDA line. An external pull-up resistor or cur-
rent source is required. Internally tied to SDAI in SSOP
package.
SDAI: Serial Bus Data Input. A high impedance input for
shifting in address, command or data bits. Normally tied
to SDAO to form the SDA line. Internally tied to SDAO in
SSOP package.
SDA (SSOP Package): Serial Bus Data Input/Output Line.
Formed by internally tying the SDAO and SDAI lines to-
gether. An external pull-up resistor or current source is
required.
SENSE
Connect this pin to the input of the current sense resistor.
Must be connected to the same trace as V
tied to V
SENSE
the output of the current sense resistor. This pin provides
sense voltage feedback and monitoring for the current
limit, circuit breaker and ADC.
SOURCE: N-Channel MOSFET Source and ADC Input.
Connect this pin to the source of the external N-channel
MOSFET switch for gate drive return. This pin also serves as
the ADC input to monitor output voltage. The pin provides
a return for the gate pulldown circuit.
+
–
: Negative Current Sense Input. Connect this pin to
DD
(QFN Package): Positive Current Sense Input.
in SSOP package.
DD
. Internally
SS: Soft Start Input. Sets the inrush current slew rate at
start-up. Connect a 68nF capacitor to provide 5mV/ms as
the slew rate for the sense voltage in start-up. This cor-
responds to 1A/ms with a 5mΩ sense resistor. Note that
a large soft-start capacitor and a small TIMER capacitor
may result in a condition where the timer expires before
the inrush current has started. Allow an additional 10nF
of timer capacitance per 1nF of soft-start capacitor to
ensure proper start-up. Use 1nF minimum to ensure an
accurate inrush current.
TIMER: Start-Up Timer Input. Connect a capacitor be-
tween this pin and ground to set a 12.3ms/μF duration
for start-up, after which an overcurrent fault is logged if
the inrush is still current limited. The duration of the off
time is 600ms/μF when overcurrent auto-retry is enabled,
resulting in a 1:50 duty cycle. An internal timer provides
a 100ms start-up time and 5 seconds auto-retry time if
this pin is tied to INTV
timer capacitance per 1nF of soft-start (SS) capacitor to
ensure proper start-up. The minimum value for the TIMER
capacitor is 10nF .
UV: Undervoltage Comparator Input. Connect this pin
to an external resistive divider from V
at this pin falls below 1.155V, an undervoltage fault is
detected and the GATE turns off. Pulling this pin below
0.4V resets all faults and allows the GATE to turn back on.
Tie to INTV
V
lockout threshold of 2.84V and overvoltage lockout
threshold of 15.6V.
DD
: Supply Voltage Input. This pin has an undervoltage
CC
if unused.
LTC4215/LTC4215-2
CC
. Allow an additional 10nF of
DD
. If the voltage
4215fe
9