ATV61HD55Y SQUARE D, ATV61HD55Y Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/6/626/square_d_sml.jpg)
ATV61HD55Y
Manufacturer Part Number
ATV61HD55Y
Description
ALTIVAR 61 DRIVE 60 HP 575/690 VOLT
Manufacturer
SQUARE D
Datasheet
1.ATV61HD55Y.pdf
(12 pages)
Discrete output type
Maximum response time
Minimum switching current
Maximum switching current
Discrete input number
Discrete input type
Discrete input logic
Acceleration and deceleration ramps
Braking to standstill
Protection type
Insulation resistance
Frequency resolution
Type of connector
Physical interface
Transmission frame
Transmission rate
Data format
Number of addresses
Method of access
Marking
Operating position
Product weight
Width
Height
Depth
R1A, R1B, R1C configurable relay logic NO/NC, electrical durability 100000 cy-
cles
R2A, R2B configurable relay logic NO, electrical durability 100000 cycles
<= 100 ms in STO (Safe Torque Off)
R1A, R1B, R1C <= 7 ms, tolerance +/- 0.5 ms
R2A, R2B <= 7 ms, tolerance +/- 0.5 ms
Configurable relay logic 3 mA at 24 V DC
R1, R2 on inductive load, 2 A at 250 V AC, cos phi = 0.4, L/R = 7 ms
R1, R2 on inductive load, 2 A at 30 V DC, cos phi = 0.4, L/R = 7 ms
R1, R2 on resistive load, 5 A at 250 V AC, cos phi = 1, L/R = 0 ms
R1, R2 on resistive load, 5 A at 30 V DC, cos phi = 1, L/R = 0 ms
7
LI1...LI5 programmable 24 V DC, voltage limits <= 30 V, with level 1 PLC,
impedance 3500 Ohm
LI6 switch-configurable 24 V DC, voltage limits <= 30 V, with level 1 PLC,
impedance 3500 Ohm
LI6 switch-configurable PTC probe 0...6, impedance 1500 Ohm
PWR safety input 24 V DC, voltage limits <= 30 V, impedance 1500 Ohm
LI1...LI5 negative logic (sink), > 16 V (state 0), < 10 V (state 1)
LI1...LI5 positive logic (source), < 5 V (state 0), > 11 V (state 1)
LI6 (if configured as logic input)negative logic (sink), > 16 V (state 0), < 10 V
(state 1)
LI6 (if configured as logic input)positive logic (source), < 5 V (state 0), > 11 V
(state 1)
Automatic adaptation of ramp if braking capacity exceeded, by using resistor
Linear adjustable separately from 0.01 to 9000 s
S, U or customized
By DC injection
Drive against exceeding limit speed
Drive against input phase loss
Drive break on the control circuit
Drive input phase breaks
Drive line supply overvoltage
Drive line supply undervoltage
Drive overcurrent between output phases and earth
Drive overheating protection
Drive overvoltages on the DC bus
Drive power removal
Drive short-circuit between motor phases
Drive thermal protection
Motor motor phase break
Motor power removal
Motor thermal protection
> 1 MOhm at 500 V DC for 1 minute to earth
Analog input 0.024/50 Hz
Display unit 0.1 Hz
1 RJ45 for Modbus on front face
1 RJ45 for Modbus on terminal
Male SUB-D 9 on RJ45 for CANopen
2-wire RS 485 for Modbus
RTU for Modbus
20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen
4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
9600 bps, 19200 bps for Modbus on front face
8 bits, 1 stop, even parity for Modbus on front face
8 bits, odd even or no configurable parity for Modbus on terminal
1...127 for CANopen
1...247 for Modbus
Slave for CANopen
CE
Vertical +/- 10 degree
68 kg
320 mm
630 mm
290 mm
3