G7L-1A-TUB-J-CB-AC200/240 Omron, G7L-1A-TUB-J-CB-AC200/240 Datasheet - Page 12
![RELAY](/photos/9/43/94319/g7l-1a-tub-j-cb_series_sml.jpg)
G7L-1A-TUB-J-CB-AC200/240
Manufacturer Part Number
G7L-1A-TUB-J-CB-AC200/240
Description
RELAY
Manufacturer
Omron
Series
G7Lr
Specifications of G7L-1A-TUB-J-CB-AC200/240
Relay Type
General Purpose
Coil Type
Standard
Contact Form
SPST-NO (1 Form A)
Contact Rating (current)
30A
Switching Voltage
250VAC - Max
Coil Current
10.2mA
Coil Voltage
240VAC
Turn On Voltage (max)
150 VAC
Turn Off Voltage (min)
36 VAC
Mounting Type
Chassis Mount
Termination Style
Quick Connect - .250" (6.3mm)
Circuit
SPST-NO (1 Form A)
Contact Rating @ Voltage
30A @ 220VAC
Control On Voltage (max)
150 VAC
Control Off Voltage (min)
36 VAC
Coil Voltage Vac Nom
240V
Contact Current Max
30A
Contact Voltage Ac Nom
220V
Coil Resistance
21000ohm
Contact Configuration
SPST-NO
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
G7L1ATUBJCBAC200/240
G7L1ATUBJCBAC200240
Z816
G7L1ATUBJCBAC200240
Z816
Precautions
■ Handling
• To preserve initial performance, do not drop or otherwise subject
• The case is not designed to be removed during normal handling
• Use the power relay in a dry environment free from excessive dust,
• Do not allow a voltage greater than the maximum allowable coil
• Do not use the power relay outside of specified voltages and cur-
• Do not allow the ambient operating temperature to exceed the
■ Installation
• Although there are not specific limits on the installation site, it
• PCB terminal-equipped relays weigh approximately 100 g. Be sure
• Quick-connect terminals can be connected to fast on receptacle
• Allow suitable slack on leads when wiring, and do not subject the
■ Cleaning PCB Terminals
• PCB terminals have semi-sealed construction which prevents flux
■ Applications
• Compressors for package air conditioners and heater switching
• Switching controllers for power tools or motors
• Power controllers for water heaters
• Power controllers for dryers
• Lamp control, motor drivers, and power supply switching in copy
• Lighting controllers
• Power controllers for packers or food processing equipment
• Magnetron control in microwaves
316
the power relay to shock.
and operation. Doing so may affect performance.
SO
voltage to be applied continuously.
rents.
specified limit.
should be as dry and dust-free as possible.
that the PCB is strong enough to support them. We recommend
dual-side through-hole PCBs to reduce solder cracking from heat
stress.
#250 and positive-lock connectors.
terminals to excessive force.
from entering the relay base. It is recommended that the user
should apply a tape seal over the vent hole prior to wave soldering
or cleaning. The tape should then be removed after processing.
controllers
machines, facsimiles, and other OA equipment
2
, H
2
S, or organic gas.
General Purpose Relay
G7L
■ Operating Coil
• As a rule, either a battery or a DC power supply with a maximum
• When driving a transistor, check the leakage current and connect a
• Momentary voltage drops on coil input voltage should not exceed
5% ripple is used for the operating voltage for DC relays. Before
using a rectified AC supply, confirm that the ripple is not greater
than 5%. Ripple greater than this can lead to variations in the oper-
ating and reset voltages.
bleeder resistor if necessary.
one second duration after contact mating with no shock or vibra-
tion.
As excessive ripple can generate beats, the insertion of a
smoothing capacitor is recommended as shown below.