M7E-022M-1 Omron, M7E-022M-1 Datasheet - Page 10

• Manufacturer Part Number: M7E-022M-1
• Description: END CAPS
• Manufacturer: Omron
• Series: M7Er

Specifications of M7E-022M-1

• Accessory Type: End Cap
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: M7E Digital Display Series
• For Use With: M7E-20HKN1 - DSPLY DGTL NEG 12-24V RD/GRN/ORNM7E-20DRN1 - DISPLAY DIGTL NEG 12-24VDC REDM7E-12HRN2 - DISPLAY DIGTL NEG 12-24VDC REDM7E-12DRN2 - DISPLAY DIGTL NEGATIVE 12-24VDCM7E-12DRN1 - DISPLAY DIGTL NEG 12-24VDC REDM7E-12DKN2 - DSPLY DGTL NEG 12-24V RD/GRN/ORNM7E-12DKN1 - DSPLY DGTL NEG 12-24V RD/GRN/ORNM7E-08DRN2-L - DISPLAY DIGTL NEG 12-24VDC REDM7E-08DRN2 - DISPLAY DIGTL NEG 12-24VDC REDM7E-02DRN2 - DISPLAY DIGTL NEG 12-24VDC REDM7E-02DRGN2 - DISPLY DGTL NEG 12-24VDC RED/GRNM7E-02DGN2 - DISPLAY DIGTL NEG 12-24VDC GREENM7E-01UG2-A - BLANK DIGITAL DISPLAY GREENM7E-01MB4-S2 - MOTHER BOARD FOR 4DGT DISPLAYM7E-01MB2-S2 - MOTHER BOARD FOR 2DGT DISPLAYM7E-01HRP2 - DISPLAY DIGITAL POS 12-24VDC REDM7E-01HRN2 - DISPLAY DIGITAL NEG 12-24VDC REDM7E-01HGP2 - DISPLAY DIGTL POS 12-24VDC GREENM7E-01HGN2 - DISPLAY DIGTL NEG 12-24VDC GREENM7E-01DRP2 - DISPLAY DIGITAL POS 12-24VDC REDM7E-01DRN2 - DISPLAY DIGITAL NEG 12-24VDC REDM7E-01DRGN2-B - DISPLY DGTL NEG 12-24VDC RED/GRNM7E-01DRGN2 - DISPLY DGTL NEG 12-24VDC RED/GRNM7E-01DRD2 - DISPLY DGTL DYN-OUT 12-24VDC REDM7E-01DGP2 - DISPLAY DIGTL POS 12-24VDC GREENM7E-01DGN2-B - DISPLAY DIGTL NEG 12-24VDC GREENM7E-01DGN2 - DISPLAY DIGTL NEG 12-24VDC GREENM7E-01DGD2 - DISPLY DGTL DYN-OUT 12-24VDC GRNM7E-01BRP2 - DISPLAY DIGTL POS 12-24VDC REDM7E-01BRN2 - DISPLAY DIGTL NEG 12-24VDC REDM7E-01BGN2 - DISPLAY DIGTL NEG 12-24VDC GREEN
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: M7E022M1

2. M7E-01@@P2 Positive Logic Model
Connected to C500-OD211 or C200H-OD215
PLC Dynamic
Output Unit
2. Connected to C200-OD215 Transistor Output Unit
PLC Dynamic
Output Unit
COM (0 V)
Signal name
+24 VDC
1. M7E-01@@D2 Dynamic Output Model
1. Connected to C500-OD211 Transistor Output Unit
Pin No.
Using Dynamic Output Units
+24
VDC
http://www.ia.omron.com/
12 to
24 VDC
An external pull-up resistor is required.
Pull-up resistor:
2.0 to 3.9 kΩ
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
PLC
PLC
PLC
Note: 1. Supply 24 VDC only. The
Note:
SW1 (dynamic output mode) ON
SW2
SW3
SW4
SW5 (positive logic output)
SW6
2. The resistance of the pull-
DATA0
to 7
DATA0
to 7
STB0
to 7
STB0
to 7
DATA0
to 7
STB0
to 7
PLC does not operate with
the M7E Negative Logic
Model.
up resistor is 2.0 to 3.9 k
(1 W). A resistance of
3.3 k is recommended.
1.
2.
A to D,
DP, LE
A to D,
DP, LE
A to D,
DP, LE
When using the C200H-
OD215, the selector on the rear
cover of the C200H-OD215
must be set as follows:
Refer to the C200H High-
density I/O Unit operation
manual for the C200H-OD215
and refer to the hardware
section of the C500 operation
manual for the C500-OD211.
Pull-up
resistor
Custom IC
Custom IC
M7E
Custom IC
OFF
OFF
OFF
ON
OFF
10