70500206 Crouzet USA, 70500206 Datasheet - Page 126
70500206
Manufacturer Part Number
70500206
Description
Y MTG BRKT FOR SW-83101-112, 1
Manufacturer
Crouzet USA
Datasheet
1.70514131.pdf
(136 pages)
Specifications of 70500206
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 126 of 136
- Download datasheet (9Mb)
3/118
Inductive Proximity Detectors – Technical Guide
Mechanical installation advice
Protection:
Electrical installation advice
Power supply:
Connection:
Connecting more than one sensor:
Series installation:
Power
source
Power
cable
3-wire DC
detectors
2-wire detectors
AC or DC
(+)
(-)
Order/Technical Support – Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com
a
a
(
(
(-)
(-)
+)
+)
BN
BU
BK
Detector 1
C
-
BN
BU
+
BN
BU
BN
BU
conduit
Metal
Load
BK
Detector 2
Detector 1
Detector x
BN
BU
Products and specifications subject to change without notice.
BK
Detector x
Load
Protect the cable against sharp objects or excessive heat.
Do not exert a pulling force of more than 5 kg on the cable.
The detectors are unable to withstand severe mechanical impact. The
bracket must be sufficiently rigid to resist shock and vibration.
Avoid using the detectors in a corrosive environment such as near
strong acids, etc. (e.g. Nitric Acid).
When a plastic detector is used in a chemical environment it is
advisable to first verify the plastic's resistance to the chemical.
Opposite is an example of a DC power supply for detectors using
smoothing. To ensure that the resulting voltage is less than the
maximum operating voltage of the detector, use a capacitor "C" to
remove spikes and ripples greater than ± 10 %.
Ideally, use a transformer with a secondary voltage less than your
required voltage.
Eg. 17.5 VAC from the secondary of the transformer to obtain less
than 24 VDC.
Limit the length of the cables to 100 m and the capacitance of the line
to 0.1 µF. Also separate detector cables and power cables as far as
possible.
It is possible to connect detectors in series:
- Ensure that the voltage at the terminals of each sensor is less than
- In on-state, check that there is sufficient voltage available to activate
This connection method is not possible if multivoltage sensors are
used.
With this connection method, add the voltage drop of each detector
together and deduct from the supply voltage to ensure there is
sufficient voltage to activate the load.
Note: detector 1 carries all the current for the additional detectors.
or equal to the minimum operating voltage (in off-state).
the load.
Related parts for 70500206
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
SCREW SOCKET (OT08PC)
Manufacturer:
Crouzet USA
Datasheet:
Part Number:
Description:
PANEL PLATE FOR 813
Manufacturer:
Crouzet USA
Datasheet:
Part Number:
Description:
Controller; CTD46 Dual Display Temperature, 1/16 DIN, NEMA 4X, 110/220VAC
Manufacturer:
Crouzet USA
Datasheet:
Part Number:
Description:
11R1084
Manufacturer:
Crouzet USA
Datasheet:
Part Number:
Description:
11R1086
Manufacturer:
Crouzet USA
Datasheet:
Part Number:
Description:
11R1087
Manufacturer:
Crouzet USA
Datasheet:
Part Number:
Description:
11R1089
Manufacturer:
Crouzet USA
Datasheet:
Part Number:
Description:
11R1078
Manufacturer:
Crouzet USA
Datasheet:
Part Number:
Description:
11R1079
Manufacturer:
Crouzet USA
Datasheet: