AXK6F40347YG PANASONIC EW, AXK6F40347YG Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/5/513/panasonic_ew_sml.jpg)
AXK6F40347YG
Manufacturer Part Number
AXK6F40347YG
Description
Header Connector,PCB Mount,PLUG,40 Contacts,SKT,0.02 Pitch,SURFACE MOUNT Terminal
Manufacturer
PANASONIC EW
Datasheet
1.AXK5F10347YG.pdf
(10 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AXK6F40347YG
Manufacturer:
PANASONIC
Quantity:
6 000
Company:
Part Number:
AXK6F40347YG
Manufacturer:
Panasonic Electric Works
Quantity:
191
NOTES FOR USING SMD TYPE CONNECTORS (Common)
Handling Single
Components
1) Make sure not to drop or allow parts to
fall from work bench
2) Excessive force applied to the
terminals could cause them to warp,
come out, or weaken the adhesive
strength of the solder. Handle with care.
3) Repeated bending of the terminals
may break them.
4) Do not use alcohol for cleaning. Doing
so may whiten the surface of molded
parts.
Storage of connectors
1) To prevent trouble from voids or air
pockets by heat of reflow soldering, avoid
storing the connectors in areas of high
humidity. When storing the connectors for
more than six months, be sure to store
them in a storage area where the
humidity is properly controlled.
2) Depending on the connector type, the
color of the connector may vary from
connector to connector if produced at
Other Notes
1) These products are made for the
design of compact and lightweight
devices and therefore the thickness of the
molded components has been made very
thin. Therefore, be careful during
insertion and removal operations for
excessive forces applied may damage
the products.
2) Dropping of the products or rugged
mishandling may bend or damage the
terminals and even hinder proper reflow
soldering.
Regarding sample orders to confirm proper mounting
When ordering samples to confirm
proper mounting with the placement
machine, connectors are delivered in 50-
piece units in the condition given right.
Consult a sale representative for ordering
sample units.
Embossed tape
amount required for
the mounting
Condition when delivered from factory
sample production
Required number
of products for
(Unit 50 pcs.)
Cleaning flux from PC board
1) To increase the cleanliness of the
cleaning fluid and cleaning operations,
prepare equipment for a cleaning
process that begins with boil cleaning,
ultrasonic cleaning, and then to vapor
cleaning.
2) Carefully oversee the cleanliness of
the cleaning fluids to make sure that the
contact surfaces do not become dirty
from the cleaning fluid itself.
3) Since some powerful cleaning may
dissolve molded components of the
connector and wipe off printed letters, we
recommend aqua pura electronic parts
cleaners. Consult us if you wish other
types of cleaning fluids.
4) Please note that the surfaces of
molded parts may whiten when cleaned
with alcohol.
different times, and some connectors
more even change color slightly if
subjected to ultraviolet rays during
storage. This is normal and will not affect
the operation of the connector.
3) When storing the connectors with the
PC boards assembled and components
alreeady set, be careful not to stack them
up so the connectors are subjected to
excessive forces.
3) Before soldering, try not to insert or
remove the connector more than
absolutely necessary.
4) When coating the PC board after
soldering the connector to prevent the
deterioration of insulation, perform the
coating in such a way so that the coating
does not get on the connector.
5) There may be variations in the colors
of products from different production lots.
This is normal.
6) The connectors are not meant to be
(Delivery can also be made on a reel by
customer request.)
Reel
panasonic-electric-works.net/ac
Handling the PC board
• Handling the PC board after
mounting the connector
When cutting or bending the PC board
after mounting the connector, be careful
that the soldered sections are subjected
to excessive forces.
4) Avoid storing the connectors in
locations with excessive dust. The dust
may accumulate and cause improper
connections at the contact surfaces.
used for switching.
7) Be sure not to allow external pressure
to act on connectors when assembling
PCBs or moving in block assemblies.
For other details, please verify with
the product specification sheets.
Do not the soldered areas to be subjected to forces