V680-HAM42-DRT Omron, V680-HAM42-DRT Datasheet - Page 23

• Manufacturer Part Number: V680-HAM42-DRT
• Description: V680 DeviceNet RFID Ctrl
• Manufacturer: Omron

Specifications of V680-HAM42-DRT

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Safety Precautions
Note: This catalog is intended only to help select the appropriate
To ensure safety, be sure to follow the following precautions:
1. Do not operate this product in any flammable, explosive, or corro-
2. Do not disassemble, repair, or remodel this product.
3. If any cable has a locking mechanism, be sure to check that it has
4. The DC power supply must be within the specified rating (24 VDC
5. Do not reverse the power supply connection.
6. Do not insert water, wire, etc., into any of the gaps in the case.
7. Make sure that the Unit is provided with sufficient ventilation
8. Do not install the Products near any equipment that generates a
9. Turn OFF the Controller or ID Sensor Unit power before attaching
10.In the event that the product exhibits any abnormal condition,
11.Dispose of this product as industrial waste.
12.Do not clean the Products with paint thinner, benzene, acetone,
13.If multiple Antennas are mounted near each other, communica-
14.To remove the Unit, catch a tool on the hook and gently remove
15.Do not perform wiring incorrectly or short-circuit the load. Doing
16.Do not use the product in environments subject to oil.
17.Do not use the product with an AC power supply.
Please observe the following precautions to prevent failure to
operate, malfunctions, or undesirable effects on product
performance.
Installation Site
Install the product at a location where:
• It is not exposed to corrosive gases, dust, metal chips, or salt.
• The ambient operating temperature is within the range stipulated in
• There are no sudden variations in temperature (no condensation).
• The ambient operating humidity is within the range stipulated in the
• No vibration or shock exceeding the values stipulated in the
• It is not subject to splashing water, oil, or chemical substances.
Do not use this product as a detection device to protect
people.
the specifications.
specifications.
specifications is transmitted directly to the body of the product.
sive gas environment.
been locked before using it.
+10%/−15%).
Doing so may cause fire or electric shock.
space.
large amount of heat (such as heaters, transformers, and large-
capacity resistors).
or removing the Read/Write Antenna.
immediately stop using the system, turn OFF the power, and con-
tact your OMRON sales representative.
or kerosene.
tions performance may decrease due to mutual interference.
Refer to the User's Manual (Cat. No. Z278 or Z279) and check to
make sure there is no mutual interference between the Antennas.
the Unit.
so may result in rupture or damage from burning.
product. Be sure to read the User's Manual for usage
precautions prior to using the product.
Precautions for Correct Use
Precautions for Safe Use
WARNING
V680-HAM42-DRT, V680-HAM91/-HAM81
Installation
• The product uses the 13.56-MHz frequency band to communicate
• To minimize the general influence of noise, observe the following
• Always bundle the cables connected to the power supply terminals
• Do not pull on the cables with excessive strength.
• Do not use products that are not waterproof in misty environments.
• Do not subject the products to chemicals that adversely affect
• When installing the product, tighten screws to the following torque:
• When Read/Write Antennas are mounted side-by-side, mutual
Host Communications (V680-HAM91/-HAM81)
When the Product is started, unstable signals may be output from
the host interface.
Begin performing controls with the Product only after it has been
started for at least 1 second.
Storage
Store the product at a location where:
• It is not exposed to corrosive gases, dust, metal chips, or salt.
• The ambient storage temperature is within the range stipulated in
• There are no sudden variations in temperature (no condensation).
• The ambient storage humidity is within the range stipulated in the
• No vibration or shock exceeding the values stipulated in the
• It is not subject to splashing water, oil, or chemical substances.
Cleaning
Do not use thinner, benzene, acetone, or kerosene for cleaning.
Using these substances may dissolve the resin material and the
case.
with ID Tags. Some devices, such as some motors, inverters, and
switching power supplies, generate electromagnetic waves (i.e.,
noise) that can affect communications with ID Tags. If any of these
devices are nearby, communications with ID Tags may be affected
or ID Tags may be destroyed. If the product is to be used near such
devices, check the effects on communications before using the
product.
precautions:
1. Ground any metallic material located around this device to
2. Keep the product away from high voltage and heavy current.
and the ground terminal and connect the enclosed ferrite core
(ZCAT2032-0930 manufactured by TDK) (V680-HAM42-DRT
only).
product materials.
V680-HS51 Read/Write Antenna: 6 N·m
V680-HS52 Read/Write Antenna: 40 N·m
V680-HS63 Read/Write Antenna: 1.2 N·m
V680-HS65 Read/Write Antenna: 0.7 to 1.2 N·m
interference may reduce the transmission performance. Refer to
the RFID System Amplifier and Antennas/ID Tags User's Manual to
mount them in a way that will prevent mutual interference.
the specifications.
specifications.
specifications is transmitted directly to the body of the product.
100 Ω or less.
23