P7S-14F Omron, P7S-14F Datasheet - Page 18

• Manufacturer Part Number: P7S-14F
• Description: Contact OSTI
• Manufacturer: Omron
• Series: G7Sr
• Type: Socketr

Specifications of P7S-14F

• Number Of Positions: 14
• Mounting Type: DIN Rail
• Termination Style: Screw Terminal
• Socket Mounting: DIN Rail
• Socket Terminals: Screw
• Voltage Rating: 24VDC
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: G7S Series
• For Use With: Z2362 - RELAY SAFETY 6A 24VDC PLUG-INZ2363 - RELAY SAFETY 6A 24VDC PLUG-IN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: P7S14F; Z2417

G-10 Automatic Mounting of PCB Relays
A Through-hole PCBs
When mounting a Relay to a PCB, take the following points into consideration for each
process. There are also certain mounting precautions for individual Relays, so refer to the
individual Relay precautions as well.
Flux Application
Continued next
Preheating
Process 1
Placement
Process 2
Process 3
Process 4
Soldering
page.
Flux
Heater
http://www.ia.omron.com/
Note: For lead-free solder, perform the soldering under conditions that conform to the applicable specifications.
1. Flow soldering is recommended to assure a uniform
• Solder: JIS Z3282 or H63A
• Solder temperature and soldering time: Approx. 250°C
• Solder time: 5 s max. (DWS: Approx. 2 s for first time
• Adjust the level of the molten solder so that the PCB is
Applicability of Automatic Soldering
1. Do not bend any terminals of the Relay to use it as a self-clinching Relay.
2. Execute PCB processing correctly according to the PCB process diagrams.
1. The G7S has no protection against flux
2. The flux must be a non-corrosive rosin-based flux
1. Preheating is required to create the optimum
2. The following conditions apply for preheating.
NO
(DWS: Approx. 260°C)
and approx. 3 s for second time)
not flooded with solder.
Temperature
Time
solder joint.
The initial performance characteristics of the Relay will be lost.
penetration, so absolutely do not use the method
shown in the diagram on the right, in which a
sponge is soaked with flux and the PCB pressed
down on the sponge. If this method is used for the
G7S, it will cause the flux to penetrate into the
Relay. Be careful even with the flux-resistant
G7SA, because flux can penetrate into the Relay
if it is pressed too deeply into the sponge.
suitable for the Relay's structural materials.
For the flux solvent, use an alcohol-based solvent,
which tends to be less chemically reactive.
Apply the flux sparingly and evenly to prevent
penetration into the Relay.
When dipping the Relay terminals into liquid flux,
be sure to adjust the flux level, so that the upper
surface of the PCB is not flooded with flux.
conditions for soldering.
G7S
Automatic soldering
100°C max.
1 min max.
YES
G7SA
(c)Copyright OMRON Corporation 2007 All Rights Reserved.
1. Smooth the solder with the tip of the iron, and then
• Solder: JIS Z3282, H60A, or H63A
• Soldering iron: Rated at 30 to 60 W
• Tip temperature: 280 to 300°C
• Soldering time: Approx. 3 s max.
2. As shown in the above illustration, solder is available
Applicability of Manual Soldering
YES
(containing rosin-based flux)
3. Make sure that flux does not adhere anywhere
Applicability of Dipping Method
3. Do not use a Relay if it has been left at a high
Applicability of Preheating
NO
NO
perform the soldering under the following conditions.
with a cut section to prevent flux from splattering.
outside of the Relay terminals. If flux adheres to
an area such as the bottom surface of the Relay, it
will cause the insulation to deteriorate.
temperature for a long period of time due to a
circumstance such as equipment failure. These
conditions will cause the Relay's initial
characteristics to change.
G7S
G7S
G7S
Example of incorrect method
Manual soldering
Sponge soaked with
flux
Pressing deeply
YES
Relay
YES
(Must be checked when
spray flexor is used.)
YES
G7SA
PCB
G7SA
G7SA
Flux
Solder
C-13