XS2C-D422 Omron, XS2C-D422 Datasheet - Page 25

• Manufacturer Part Number: XS2C-D422
• Description: CONNECTOR
• Manufacturer: Omron
• Series: XS2r

Specifications of XS2C-D422

• Connector Type: Receptacle, Female Sockets
• Number Of Positions: 4
• Mounting Type: Free Hanging (In-Line), Right Angle
• Termination: Solder Cup
• Fastening Type: Threaded
• Orientation: Keyed
• Ingress Protection: IP67 - Dust Tight, Waterproof
• Shell Material, Finish: Brass, Nickel Plated
• Features: Cable Clamp
• Number Of Positions / Contacts: 4
• Contact Plating: Gold over Nickel
• Contact Material: Brass
• Gender: Female
• Current Rating: 3 A
• Mounting Style: Cable
• Termination Style: Solder
• Housing Material: Polybutylene Terephthalate
• Insulation Resistance: 1000 MOhms
• Mounting Angle: Right
• Operating Temperature Range: - 25 C to + 70 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Shell Size - Insert: -
• Shell Size, Military: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: XS2CD422

Insertion
• Five-pole Connectors
Cable End Processing
• Four-pole Connectors
• Tentatively insert the pins to the pin block holes so that the
Screw-on Connectors
• Loosen the screws on pins 1 to 4 and insert the cores
• Use the special Screwdriver (XW4Z-00B)
• Strip the cable sheath for a total of 15 mm and strip the core
• Connect the core to pin 5 (in the center) first.
• Insert the core from the side of the hold with the tab and
key on the pin block will coincide with the key groove on the
pin clamp. Then insert the cable along with the pin clamp.
according to the pin numbers.
screws securely so that the cores do not pull out (tightening
torque: 0.15 to 0.2 N·m).
covering for 8 mm for the core to connect to pin 5.
tighten the screw securely (tightening torque: 0.15 to
0.2 N·m), and then cut off the excess wire with wire cutters.
Pin Block
Screw
8
Screwdriver
Special
7
Key
8
12
±0.5
12
Conductors for
pins 1 to 4
Conductors for
pin 5
Tab
XS2C use XS2G use
Pin Clamp
6
Key groove Key groove
±0.5
Screw
*
and tighten the
Screwdriver
Special
Connecting Shielded Cables to Five-pole Connectors
*
(4) Inserting Pin Block
• Bend the cable as shown below, attached the enclosed
• Connect the cores to pins 1 to 4.
• Place the insulation tub on the drain line of the shield and
• Tighten the screw and then check visually to see if there is
• Connect the cores to pins 1 to 4.
When tightening the screws, use the dedicated XW4Z-00B
Screwdriver that matches with the screw-slot dimensions.
• Mount the cover to the pin block so that the triangle mark on
• If the cover is used for an L-shaped model, the relationship
• Fully insert the positioning key until the positioning key is
insulation cap, and then strip the other cores.
connect ti to the terminal.
insulation between the cores.
the pin block will coincide with the triangle mark on the
cover.
between the position of the polarity key on the engaged side
and cable connection direction will be determined by the
direction in which the positioning key is inserted into the
cover, which can be rotated by 90°.
hidden by the casing.
Pin Block
(Soldering Model)
(Crimping Model)
Polarity key
Lock spring
Positioning key
(triangle mark)
XW4Z-00B
Screwdriver
Drain line
O-ring
Insulation tube
Insulation cap
Cover
(Straight Model)
(L-shaped Model)
Triangle mark
XS2
25