LTC1799CS5 Linear Technology, LTC1799CS5 Datasheet
LTC1799CS5
Specifications of LTC1799CS5
Available stocks
Related parts for LTC1799CS5
LTC1799CS5 Summary of contents
Page 1
... Ceramic Oscillator Replacement ■ Small Footprint Replacement for Econ Oscillators , LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. ThinSOT is a trademark of Linear Technology Corporation. Protected by U.S. Patents including 6342817 and 6614313. ...
Page 2
... SET 10k, Pin ∞ SET Pin Pin ORDER PART NUMBER LTC1799CS5 5 OUT LTC1799IS5 LTC1799HS5 4 DIV S5 PART MARKING LTND = 256°C/W LTNE LTND = 5pF, unless otherwise noted. L MIN TYP MAX UNITS ±0.5 ±1.5 ● ±2 ● ±2.5 ±2.5 ±2.5 ±0.5 ± ...
Page 3
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifications are at T All voltages are with respect to GND. SYMBOL PARAMETER V High Level Output Voltage (Note Low Level Output Voltage (Note OUT Rise Time r (Note ...
Page 4
LTC1799 W U TYPICAL PERFOR A CE CHARACTERISTICS Frequency Variation vs R SET 25°C A GUARANTEED LIMITS APPLY 3 OVER 5k TO 200k RANGE –1 –2 –3 – SET Peak-to-Peak Jitter ...
Page 5
CTIO (Pin 1): Voltage Supply (2.7V ≤ V must be kept free from noise and ripple. It should be bypassed directly to a ground plane with a 0.1µF capacitor. GND (Pin 2): ...
Page 6
LTC1799 THEORY OF OPERATIO As shown in the Block Diagram, the LTC1799’s master oscillator is controlled by the ratio of the voltage between + the V and SET pins and the current entering the SET pin (I ). The voltage ...
Page 7
U U APPLICATIO S I FOR ATIO SELECTING THE DIVIDER SETTING AND RESISTOR The LTC1799’s master oscillator has a frequency range spanning 0.1MHz to 33MHz. However, accuracy may suffer if the master oscillator is operated at greater than 10MHz with ...
Page 8
LTC1799 U U APPLICATIO S I FOR ATIO POWER SUPPLY REJECTION Low Frequency Supply Rejection (Voltage Coefficient) Figure 5 shows the output frequency sensitivity to power supply voltage at several different temperatures. The LTC1799 has a conservative guaranteed voltage coeffi- ...
Page 9
U U APPLICATIO S I FOR ATIO Jitter The typical jitter is listed in the Electrical Characteristics and shown in the Typical Performance Characteristics. These specifications assume that the capacitance on SET (Pin 3) is limited to less than 10pF, ...
Page 10
LTC1799 Once known, calculate R IN SET 10 MHz • • = SET N f OSC MAX ( ) ⎡ R ⎛ − ⎜ ⎢ ...
Page 11
... MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. U ...
Page 12
... TA08 1400 1200 10MHz 10k f = • OSC 1000 800 600 400 200 www.linear.com ● 5 OUT 4 DIV Output Frequency vs Temperature MAX TYP MIN 0 –20 – TEMPERATURE (°C) 1799 TA04 LT/TP 0804 1K REV B • PRINTED IN USA © LINEAR TECHNOLOGY CORPORATION 2001 sn1799 1799fbs ...