MAX158BCPI Maxim Integrated Products, MAX158BCPI Datasheet - Page 6

• Manufacturer Part Number: MAX158BCPI
• Description: Audio A/D Converter ICs Integrated Circuits (ICs)
• Manufacturer: Maxim Integrated Products

Specifications of MAX158BCPI

• Conversion Rate: 400 KSPs
• Resolution: 8 bit
• Number Of Adc Inputs: 8
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Supply Voltage (max): 5.25 V
• Supply Voltage (min): 4.75 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The MAX154/MAX158 use what is commonly called a
"half-flash" conversion technique (Figure 3). Two 4-bit
flash ADC converter sections are used to achieve an 8-
bit result. Using 15 comparators, the upper 4-bit MS
(most significant) flash ADC compares the unknown
input voltage to the reference ladder and provides the
upper four data bits.
An internal DAC uses the MS bits to generate an analog
signal from the first flash conversion. A residue voltage
representing the difference between the unknown input
and the DAC voltage is then compared to the reference
ladder by 15 LS (least significant) flash comparators to
obtain the lower four output bits.
The operating sequence is shown in Figure 4. A conver-
sion is initiated by a falling edge of RD and CS. The
comparator inputs track the analog input voltage for
approximately 1µs. After this first cycle, the MS flash
result is latched into the output buffers and the LS con-
version begins. INT goes low approximately 600ns later,
indicating the end of the conversion, and that the lower
four bits are latched into the output buffers. The data
can then be accessed using the CS and RD inputs.
CMOS High-Speed 8-Bit ADCs with
Multiplexer and Reference
Figure 3. Functional Diagram
6
_______________Detailed Description
_______________________________________________________________________________________
V
*MAX154 – 4-Channel Mux
V
REF OUT
AIN1
AIN4
AIN8
MAX158 – 8-Channel Mux
REF
REF
+
-
2.5V
REF
MUX*
Converter Operations
Operating Sequence
A0
ADDRESS
DECODE
LATCH
A1
A2
16
V
REF
+
The MAX154/MAX158 use only Chip Select (CS) and
Read (RD) as control inputs. A READ operation, taking
CS and RD low, latches the multiplexer address inputs
and starts a conversion (Table 1).
There are two interface modes, which are determined
by the length of the RD input. Mode 0, implemented by
keeping RD low until the conversion ends, is designed
for microprocessors that can be forced into a WAIT
state. In this mode, a conversion is started with a READ
operation (taking CS and RD low), and data is read
when the conversion ends. Mode 1, on the other hand,
does not require microprocessor WAIT states. A READ
operation simultaneously initiates a conversion and
reads the previous conversion result.
Table 1. Truth Table for Input Channel
Selection
___________________Digital Interface
MAX154/MX7824
0
0
1
1
A1
(4MSB)
FLASH
FLASH
(4LSB)
4-BIT
4-BIT
4-BIT
ADC
DAC
ADC
RDY
A0
0
1
0
1
TIMING AND CONTROL
CIRCUITRY
CS
A2
0
0
0
0
1
1
1
1
MAX158/MX7828
A1
0
0
1
1
0
0
1
1
DRIVERS
THREE-
RD
STATE
A0
0
1
0
1
0
1
0
1
SELECTED
CHANNEL
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
AIN8
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
INT