DS1375T Maxim Integrated Products, DS1375T Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS1375T
Manufacturer Part Number
DS1375T
Description
Real Time Clock
Manufacturer
Maxim Integrated Products
Datasheet
1.DS1375T.pdf
(13 pages)
Specifications of DS1375T
Function
Clock, Calendar, Alarm
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.7 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Rtc Bus Interface
Serial
Package / Case
TDFN EP
Time Format
HH:MM:SS
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Figures 4 and 5 detail how data transfer is accom-
plished on the I
the R/W bit, two types of data transfer are possible:
during the low period of the clock signal. There is
one clock pulse per bit of data.
Each data transfer is initiated with a START condi-
tion and terminated with a STOP condition. The
number of data bytes transferred between the
START and the STOP conditions is not limited, and
is determined by the master device. The informa-
tion is transferred byte-wise and each receiver
acknowledges with a ninth bit.
Acknowledge: Each receiving device, when
addressed, is obliged to generate an acknowledge
after the reception of each byte. The master device
must generate an extra clock pulse that is associat-
ed with this acknowledge bit.
A device that acknowledges must pull down the
SDA line during the acknowledge clock pulse in
such a way that the SDA line is stable low during
the high period of the acknowledge-related clock
pulse. Setup and hold times must be taken into
account. A master must signal an end of data to the
slave by not generating an acknowledge bit on the
last byte that has been clocked out of the slave. In
this case, the slave must leave the data line high to
enable the master to generate the STOP condition.
Data transfer from a master transmitter to a
slave receiver. The first byte transmitted by the
master is the slave address. Next follows a number
of data bytes. The slave returns an acknowledge bit
after each received byte.
Data transfer from a slave transmitter to a mas-
ter receiver. The master transmits the first byte (the
slave address). The slave then returns an acknowl-
edge bit. Next follows a number of data bytes
transmitted by the slave to the master. The master
returns an acknowledge bit after all received bytes,
other than the last byte. At the end of the last
received byte, a not acknowledge is returned.
The master device generates all the serial clock
pulses and the START and STOP conditions. A
transfer is ended with a STOP condition or with a
repeated START condition. Since a repeated
START condition is also the beginning of the next
serial transfer, the bus is not released.
2
C bus. Depending upon the state of
I
____________________________________________________________________
2
C Digital Input RTC with Alarm
The DS1375 can operate in the following two modes:
Slave Receiver Mode (Write Mode): Serial data
and clock are received through SDA and SCL. After
each byte is received, an acknowledge bit is trans-
mitted. START and STOP conditions are recog-
nized as the beginning and end of a serial transfer.
Address recognition is performed by hardware
after reception of the slave address and direction
bit. The slave address byte is the first byte received
after the master generates the START condition.
The slave address byte contains the 7-bit DS1375
address, which is 1101000, followed by the direc-
tion bit (R/W), which is 0 for a write. After receiving
and decoding the slave address byte, the DS1375
outputs an acknowledge on SDA. After the DS1375
acknowledges the slave address + write bit, the
master transmits a word address to the DS1375.
This sets the register pointer on the DS1375, with
the DS1375 acknowledging the transfer. The mas-
ter can then transmit zero or more bytes of data,
with the DS1375 acknowledging each byte
received. The register pointer increments after
each data byte is transferred. The master gener-
ates a STOP condition to terminate the data write.
Slave Transmitter Mode (Read Mode): The first
byte is received and handled as in the slave receiv-
er mode. However, in this mode, the direction bit
indicates that the transfer direction is reversed. The
DS1375 transmits serial data on SDA while the seri-
al clock is input on SCL. START and STOP condi-
tions are recognized as the beginning and end of a
serial transfer. Address recognition is performed by
hardware after reception of the slave address and
direction bit. The slave address byte is the first byte
received after the master generates the START
condition. The slave address byte contains the 7-bit
DS1375 address, which is 1101000, followed by
the direction bit (R/W), which is 1 for a read. After
receiving and decoding the slave address byte, the
DS1375 outputs an acknowledge on SDA. The
DS1375 then begins to transmit data starting with
the register address pointed to by the register
pointer. If the register pointer is not written to before
the initiation of a read mode, the first address that
is read is the last one stored in the register pointer.
The DS1375 must receive a not acknowledge to
end a read.
11