LAN9500I-ABZJ-TR SMSC, LAN9500I-ABZJ-TR Datasheet - Page 46

• Manufacturer Part Number: LAN9500I-ABZJ-TR
• Description: Ethernet ICs USB 2.0 to 10/100 Ethernet CTRL TR
• Manufacturer: SMSC

Specifications of LAN9500I-ABZJ-TR

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Chapter 8 Operational Characteristics
Revision 1.0 (05-17-10)
8.1
8.2
Absolute Maximum Ratings*
Operating Conditions**
Supply Voltage (VDD33IO, VDD33A)
Positive voltage on signal pins, with respect to ground
Negative voltage on signal pins, with respect to ground
Positive voltage on XI, with respect to ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.6V
Positive voltage on XO, with respect to ground. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +2.5V
Ambient Operating Temperature in Still Air (T
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55
Lead Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to JEDEC Spec. J-STD-020
HBM ESD Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IEC61000-4-2 Contact Discharge ESD Performance
IEC61000-4-2 Air-Gap Discharge ESD Performance
Note 8.1
Note 8.2
Note 8.3
Note 8.4
Note 8.5
Note 8.6
*Stresses exceeding those listed in this section could cause permanent damage to the device. This is
a stress rating only. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Functional operation of the device at any condition exceeding those indicated in
Section 8.2, "Operating
of this specification is not implied. Note, device signals are NOT 5 volt tolerant unless specified
otherwise.
Supply Voltage (VDD33A, VDD33BIAS, VDD33IO) . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.3V +/- 300mV
Ambient Operating Temperature in Still Air (T
**Proper operation of the device is guaranteed only within the ranges specified in this section.
When powering this device from laboratory or system power supplies, it is important that
the absolute maximum ratings not be exceeded or device failure can result. Some power
supplies exhibit voltage spikes on their outputs when AC power is switched on or off. In
addition, voltage transients on the AC power line may appear on the DC output. If this
possibility exists, it is suggested that a clamp circuit be used.
This rating does not apply to the following pins: XI, XO, EXRES, USBRBIAS.
This rating does not apply to the following pins: EXRES, USBRBIAS.
0
+/-8kV for LAN9500/LAN9500i, +/-5kV for LAN9500A/LAN9500Ai
Performed by independent 3rd party test facility.
o
C to +70
o
Conditions**",
C for commercial version, -40
DATASHEET
(Note
Section 8.4, "DC
46
8.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to +3.6V
A
A
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(Note
(Note
o
C to +85
(Note
Specifications", or any other applicable section
(Note
8.6) . . . . . . . . . . . . . . . . . . . . . . . . . .+/-8kV
8.6) . . . . . . . . . . . . . . . . . . . . . . . . .+/-15kV
8.2) . . . . . . . . . . . . . . . . . . . . . . . . . . +6V
8.3) . . . . . . . . . . . . . . . . . . . . . . . . -0.5V
o
C for industrial version.
USB 2.0 to 10/100 Ethernet Controller
SMSC LAN950x Family
o
C to +150
Datasheet
.Note 8.5
Note 8.4
Note 8.4
o
C