LX256EB-5FN484C Lattice, LX256EB-5FN484C Datasheet - Page 20
![no-image](/images/manufacturer_photos/0/3/380/lattice_sml.jpg)
LX256EB-5FN484C
Manufacturer Part Number
LX256EB-5FN484C
Description
Analog & Digital Crosspoint ICs E-Series, 256 I/O Switch Matrix, 2.5V, 5ns, Pb-Free
Manufacturer
Lattice
Datasheet
1.LX256EV-5FN484C.pdf
(75 pages)
Specifications of LX256EB-5FN484C
Maximum Dual Supply Voltage
2.7 V
Minimum Dual Supply Voltage
2.3 V
Mounting Style
SMD/SMT
Number Of Arrays
1
Operating Supply Voltage
2.5 V
Supply Type
Triple
Configuration
256 x 256
Package / Case
FPBGA-484
Data Rate
38 Gbps
Input Level
Bus LVDS, LVCMOS, LVDS, LVPECL, LVTTL
Output Level
Bus LVDS, LVCMOS, LVDS, LVPECL, LVTTL
Maximum Operating Temperature
+ 90 C
Minimum Operating Temperature
0 C
Product
Digital Crosspoint
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lattice Semiconductor
High Speed Serial Interface Block (sysHSI Block)
The High Speed Serial Interface (sysHSI) allows high speed serial data transfer over a pair of LVDS I/O. The
ispGDX2 devices have multiple sysHSI Blocks.
Each sysHSI Block has two SERDES blocks which contain two main sub-blocks, Transmitter (with a serializer) and
Receiver (with a deserializer) including Clock/Data Recovery Circuit (CDR). Each SERDES can be used as a full
duplex channel. The two SERDES in a given sysHSI Block share a common clock and must operate at the same
nominal frequency. Figure 14 shows the sysHSI Block.
Device features support two data coding modes: 10B/12B and 8B/10B (for use with other encoding schemes, see
Lattice’s sysHSI application notes). The encoding and decoding of the 10B/12B standard are performed within the
device in dedicated logic. For the 8B/10B standard, the symbol boundaries are aligned internally but the encoding
and decoding are performed outside the device.
Each SERDES block receives a single high speed serial data input stream (with embedded clock) from an input,
and provide a low speed 10-bit wide data stream and a recovered clock to the device. For transmitting, the SER-
DES converts a 10-bit wide low-speed data stream to a single high-speed data stream with embedded clock for
output.
Additionally, multiple sysHSI Blocks can be grouped together to form a source synchronous interface of between 1-
8 channels.
Figure 15 shows the connections of the SERDES block with the FIFO, sysIO block and the MRB. Table 6 provides
the descriptions of the SERDES.
For more information on the SERDES/CDR, refer to Lattice technical note number TN1020, sysHSI Usage Guide-
lines.
Table 6. SERDES Signal Descriptions
1. “E-Series” does not support sysHSI.
CDRRSTb
SYDT
CAL
RXD
TXD
REFCLK
SIN
SOUT
SS_CLKIN
SS_CLKOUT
RECCLK
CSLOCK
Signal
Internal
Internal
Internal
Internal
Internal
I/O
O
O
O
I
I
I
I
Resets the CDR circuit of sysHSI block
Symbol alignment detect for sysHSI block
Initiates source synchronous calibration sequence
Parallel data in for sysHSI block
Parallel data out for sysHSI block
Reference clock received from the clock tree
Serial data input for sysHSI block (LVDS input)
Serial data output for sysHSI block (LVDS output)
Clock input for source synchronous group
Clock output for source synchronous group
Recovered clock from encoded data by CDR of sysHSI block
Lock output of the PLL associated with sysHSI block
17
Description
1
ispGDX2 Family Data Sheet