LAN91C111I-NE SMSC, LAN91C111I-NE Datasheet - Page 41
![no-image](/images/manufacturer_photos/0/6/617/smsc_sml.jpg)
LAN91C111I-NE
Manufacturer Part Number
LAN91C111I-NE
Description
Ethernet ICs Non-PCI 10/100 Ethernet MAC
Manufacturer
SMSC
Type
Single Chip MAC and PHYr
Datasheet
1.LAN91C111-NU.pdf
(128 pages)
Specifications of LAN91C111I-NE
Ethernet Connection Type
10 Base-T, 100 Base-TX
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Product
Ethernet Controllers
Number Of Transceivers
1
Standard Supported
802.3, 802.3u
Data Rate
10 Mbps, 100 Mbps
Supply Voltage (max)
5 V
Supply Voltage (min)
0 V
Supply Current (max)
140 mA
Maximum Operating Temperature
+ 85 C
Package / Case
TQFP-100
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
10/100 Non-PCI Ethernet Single Chip MAC + PHY
Datasheet
SMSC LAN91C111 REV C
7.7.15
7.7.16
7.7.17
7.7.18
Autopolarity Disable
The autopolarity feature can be disabled by setting the autopolarity disable bit in the PHY MI serial
port Configuration 2 register.
Full Duplex Mode
100 Mbps
Full Duplex mode allows transmission and reception to occur simultaneously. When Full Duplex mode
is enabled, collision is disabled.
The device can be either forced into Half or Full Duplex mode, or the device can detect either Half or
Full Duplex capability from a remote device and automatically place itself in the correct mode.
The device can be forced into the Full or Half Duplex modes by either setting the duplex bit in the MI
serial port Control register.
The device can automatically configure itself for Full or Half Duplex modes by using the
AutoNegotiation algorithm to advertise and detect Full and Half Duplex capabilities to and from a
remote terminal. All of this is described in detail in the Link Integrity and AutoNegotiation section.
10 Mbps
Full Duplex in 10 Mbps mode is identical to the 100 Mbps mode.
100/10 Mbps SELECTION
General
The device can be forced into either the 100 or 10 Mbps mode, or the device also can detect 100 or
10 Mbps capability from a remote device and automatically place itself in the correct mode.
The device can be forced into either the 100 or 10 Mbps mode by setting the speed select bit in the
PHY MI serial port Control register assuming AutoNegotiation is not enabled.
The device can automatically configure itself for 100 or 10 Mbps mode by using the AutoNegotiation
algorithm to advertise and detect 100 and 10 Mbps capabilities to and from a remote terminal. All of
this is described in detail in the Link Integrity & AutoNegotiation section.
Loopback
Diagnostic Loopback
A diagnostic loopback mode can also be selected by setting the loopback bit in the MI serial port
Control register. When diagnostic loopback is enabled, transmit data at internal MII is looped back
onto receive data output at internal MII, transmit enable signal is looped back onto carrier sense output
at internal MII, the TP receive and transmit paths are disabled, the transmit link pulses are halted, and
the Half/Full Duplex modes do not change.
PHY Powerdown
The internal PHY of LAN91C111 can be powered down by setting the powerdown bit in the PHY Ml
serial port Control register. In powerdown mode, the TP outputs are in high impedance state, all
functions are disabled except the PHY Ml serial port, and the power consumption is reduced to a
minimum. To restore PHY to normal power mode, set the PDN bit in PHY MI Register 0 to 0. The PHY
is then in isolation mode (MII_DIS bit is set); This MII_DIS bit is needed to be cleared. The device is
guaranteed to be ready for normal operation 500mS after powerdown is de-asserted.
PHY Interrupt
The LAN91C111 PHY has interrupt capability. The interrupt is triggered by certain output status bits
(also referred to as interrupt bits) in the serial port. R/LT bits are read bits that latch on transition.
DATASHEET
41
Revision 1.91 (06-01-09)