NC-AB MULTICORE (SOLDER), NC-AB Datasheet - Page 2
![BRAID, DESOLDERING, NO CLEAN, 1.5M](/photos/27/15/271559/4468261_sml.jpg)
NC-AB
Manufacturer Part Number
NC-AB
Description
BRAID, DESOLDERING, NO CLEAN, 1.5M
Manufacturer
MULTICORE (SOLDER)
Datasheet
1.NC-AA30M.pdf
(3 pages)
Specifications of NC-AB
Braid Material
Flux-coated Copper
Width
2.2mm
Length
1.5mm
Flux Type
No Clean
Lead Free Status / RoHS Status
na
A new No Clean Desoldering Wick designed for static-free
desoldering and repair of PC boards without the need for
subsequent cleaning.
Multicore No Clean Wick uses a special halide-free vacuumised
no-clean, flux-coated copper braid designed to improve wicking.
It will not lose its efficiency even after prolonged storage in humid
conditions. The wick remains flexible and will not flake. PC
boards meet MIL-P-28809A Cleanliness Test without cleaning.
Multicore No Clean Wick is available in five sizes, including a
Microwick size (NC-MW) for SMD replacement. Each size has
colour coded packaging for easy identification and is supplied on
1.5m or 3m static dissipative spools meeting DOD standards.
Lay Multicore No Clean Wick over the solder requiring removal
and place the soldering iron tip on top of the copper braid. The
braid and solder beneath will gradually heat until the solder melts
and is absorbed into the braid by capillary action. Remove the
braid, cut off the solder-filled length and dispose of lead
contaminated copper properly.
Sudden heat shock, which may be produced when using a
preheated vaccum desoldering tool, is prevented since the braid
is cold when it first comes into contact with the joint to be
desoldered.
Multicore No Clean Wick is supplied on static dissipative spools
conforming to both (DOD) Standard 1686 and DOD Handbook
263 for static discharge protection and meets the decay rate
provision of MIL-B-81705B.
Specially processed copper braid is coated with a reduced
volume of time tested Xersin 2005 halide free synthetic resin, so
that the quantity of residue after use is significantly less than with
conventional desoldering wick. Xersin 2005 meets Bellcore TR-
TSY 000078 issue 2, ANSI/IPC SF-818 and is rated IPC-LR3CN.
PCBs will pass the MIL-P-28809A Cleanliness Test without
cleaning, provided a No Clean flux and a clean system and
components are used. PCBs will also pass this test if they have
been cleaned after the soldering operation, provided they have
been reworked using a No Clean flux in a clean environment.
MSL525
DESCRIPTION
APPLICATION
SPECIAL PROPERTIES
Loctite Electronics
Henkel Loctite UK Ltd, Watchmead, Welwyn Garden City, Hertfordshire, AL7 1JB, England
UK.: 01707 358800
Loctite is a Trademark of Henkel Loctite Corp. U.S.A
Multicore No Clean Wick is supplied in static dissipative plastic
spools of 1.5m (5 ft) each. This provides convenient application
and protects the user from heat.
Packaged ten static dissipative spools per vacuum packed sleeve
and five sleeves per box for a total of fifty spools per carton. Also
available in 100 ft Econo-spools.
Due to the nature of the Xersin 2005 flux coating, Multicore No
Clean Wick does not lose its efficiency even after prolonged
storage in humid conditions, whereas conventional rosin coated
wicks may lose their efficiency under such conditions.
WARNING: The following information is for guidance only and
users must refer to the Material Safety Data Sheet relevant to
Multicore No Clean Desoldering Wick before use.
Fume Hazards and Precautions: The fumes evolved during
use may irritate the nose and respiratory organs of some
sensitive subjects. Avoid excessive inhalation of the fumes.
Suitable fume extraction equipment should be used to extract
fumes away from the operators. When used at normal soldering
temperatures the amount of lead fume given off is negligible.
Protection and Hygiene: Eating, drinking and smoking should
not be permitted in the working area. Hands should be washed
with soap and warm water after handling this product, especially
before eating.
Waste Disposal: Waste material should be disposed of in
accordance with local regulations.
Note
The data contained herein are furnished for information only and are
believed to be reliable.
results obtained by others over whose methods we have no control.
It is the user's responsibility to determine suitability for the user's
purpose of any production methods mentioned herein and to adopt
such precautions as may be advisable for the protection of property
and of persons against any hazards that may be involved in the
handling and use thereof. In light of the foregoing, Loctite
Corporation specifically disclaims all warranties expressed or
implied, including warranties of merchantability or fitness for a
particular purpose, arising from sale or use of Loctite
Corporation’s
disclaims any liability for consequential or incidental damages
of any kind, including lost profits. The discussion herein of various
processes or compositions is not to be interpreted as representation
that they are free from domination of patents owned by others or as a
license under any Loctite Corporation patents that may cover such
processes or compositions. We recommend that each prospective
user test his proposed application before repetitive use, using this
data as a guide. This product may be covered by one or more United
States or foreign patents or patent applications.
PACKAGING
SHELF LIFE
HEALTH AND SAFETY
Reference
NC-MW
NC-AA
NC-AB
NC-BB
NC-00
Size
NO CLEAN DESOLDERING WICK, May 2003
products.
0.5mm (0.02in)
0.8mm (0.03in)
1.5mm (0.06in)
2.2mm (0.08in)
2.7mm (0.10in)
We cannot assume responsibility for the
Approximate
Width
Loctite
Corporation
www.loctite.com
Label Colour
Orange
Yellow
Green
White
Code
Blue
specifically