PAXCDC10 Red Lion Controls, PAXCDC10 Datasheet - Page 17

• Manufacturer Part Number: PAXCDC10
• Description: RS485 Serial Communications Output Interface Card With Terminal Block
• Manufacturer: Red Lion Controls

Specifications of PAXCDC10

• Accessory Type: RS485 Serial Communications Output Interface Card With Terminal Block
• Brand/series: PAX Series
• Card Type: RS485 Serial Communications Output Card
• Data Rate: 7⁄8 Bits
• Standards: cULus Listed, CSA Certified and CE Marked
• Voltage, Working: 50 V
• Pax Label Kit: 189 Different Engineering Units, Labels Inserted Inside the Unit
• For Use With: Red Lion PAX Digital Input Panel Meters
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant


Shaded areas are model dependent.
Program lock-out.
by repeatedly pressing the DSP key. An annunciator indicates the display being
shown. These displays can be locked from being visible. It is recommended that
the display be set to
modified. This Programming Mode can be locked with a security code and/or
user input. When locked and the PAR key is pressed, the meter enters a Quick
Programming Mode. In this mode, setpoint, count load and scale factor values
can still be read and/or changed per the selections below. The Display Intensity
Level () parameter also appears whenever Quick Programming Mode is
enabled, and the security code is greater than zero.

6.3 MODULE 3 - D

These displays can be programmed for
Module 3 is the programming for Display lock-out and “Full” and “Quick”
When in the Display Mode, the available displays can be read consecutively
“Full” Programming Mode permits all parameters to be viewed and

SELECTION
x = Counter A , Counter B, and then Counter C
n = Setpoints 1 to 4
PAR
Throughout this document, Programming Mode (without Quick in front) always refers to “Full” Programming (all meter parameters are accessible).
SECURITY



Counter x
x
3-LOC
Lock-out
SELECTION
Display
CODE


>0
>0
>0
COUNTER A B C DISPLAY LOCK-OUT *
0
0
0


CNt


MAX. MIN. DISPLAY LOCK-OUT *
DESCRIPTION
Visible but not changeable in Quick Programming Mode
Visible and changeable in Quick Programming Mode
Not visible in Quick Programming Mode
RATE DISPLAY LOCK-OUT *

CONFIGURED
USER INPUT
not
not
DESCRIPTION
Visible in Display Mode
Not visible in Display Mode




when the corresponding function is not used.
Rate Display


Lock-out


rAtE

USER INPUT
Not Active
Not Active
————
————

STATE
Active
Active



Max Display


Lock-out
or

HI
Quick Programming w/Display Intensity
Quick Programming w/Display Intensity
.
ISPLAY AND


Quick Programming
“Full” Programming
“Full” Programming
“Full” Programming
Min Display
PROGRAMMING MODE ACCESS

WHEN PAR KEY IS
Lock-out
PARAMETER MENU
PRESSED
LO





P
Setpoint 1-4
ARAMETERS
Access
17
SP-n
P

following table). Accessible only with the Setpoint Plug-in card installed.
ROGRAM
COUNT LOAD A B C ACCESS LOCK-OUT *

SCALE FACTOR A B C ACCESS LOCK-OUT *


access the “Full” Programming Mode. Access will only be allowed after entering
a matching security code or universal code of
would not have to be configured for Program Lock-out. However, this lock-out is
overridden by an inactive user input configured for Program Lock-out.
*


The setpoint displays can be programmed for
Factory Setting can be used without affecting basic start-up.
These displays can be programmed for
The Scale Factor values can be programmed for
Entry of a non-zero value will cause the prompt


“FULL” PROGRAMMING MODE ACCESS
Immediate access.
After Quick Programming with correct code # at
After Quick Programming with correct code # at
Immediate access.
No access
Immediate access.
Count Load
x

Counter x
Access


CNtLd
Shaded areas represent program access that is model dependent.
SETPOINT 1 to 4 ACCESS LOCK-OUT *






L
(

OCK


SECURITY CODE *
x




Factor x
SCFAC
to
Access
Scale


-

OUT
)








Security
,

COdE
. With this lock-out, a user input
Code



, or



,

to appear when trying to

,


prompt.
prompt.
Pro
, or




.
, or




.
(See the





