KPEG006 Kingstate Electronics Corp., KPEG006 Datasheet - Page 5

• Manufacturer Part Number: KPEG006
• Description: RECEIVER, PIEZO, LEADS
• Manufacturer: Kingstate Electronics Corp.

Specifications of KPEG006

• Transducer Function: Piezoelectric Telephone Receiver
• Sound Level Spl: 108dB
• External Diameter: 22.5mm
• External Length / Height: 3.2mm
• Impedance: 2kohm
• Lead Length: 100mm
• Operating Temperature Max: 85°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

G. MECHANICAL CHARACTERISTICS 機械特性
H. ENVIRONMENT TEST 環境測試
No.
No.
1
2
3
4
1
2
3
(Connector excepted)
(端子類不適用此項)
High temp. Test
Low temp. Test
Lead Wire Pull
相對濕度測試
Vibration test
Humidity test
Solderability
焊錫附著性
Drop test
線材拉力
振動測試
落下測試
高溫測試
低溫測試
Strength
Item
Item
志豐電子股份有限公司 KINGSTATE ELECTRONICS CORP 5/6
Stripped wires of lead wires are immersed in rosin for 5
seconds and then immersed in solder bath of +270±5℃ for
3±0.5 seconds.
裸線部份浸入松香溶液 5 秒後,再浸入+270±5℃溶融焊鍚槽
3±0.5 秒.
The pull force shall be applied to double lead wire：
Horizontal 3.0N(0.306kg) for 30
Vertical
雙線材水平方向施以 3.0N(0.306kg) 的力量, 垂直方向施以
2.0N(0.204kg) 的力量,各 30 秒.
Receiver shall be measured after being applied vibration of
amplitude of 1.5mm with 10 to 55hz band of vibration
frequency to each of 3 per-pendicular directions for 2 hours.
振動週波數 10∼55HZ、全振幅 1.5mm 於 X.Y.Z 3 個方向,各
2 小時.
Drop the receiver contained in normal box onto the board
40mm thick 10 times from the height of 75cm
將受話器置於盒中, 自 75 公分高度落在 40mm 木板上共 10
次.
After being placed in a storage at +95℃ for 240 hours.
置於+95℃環境 240 小時.
After being placed in a storage at -40℃ for 240 hours.
置於-40℃環境中 240 小時.
After being placed in a storage at +40℃and 95±5%RH
relative humidity for 240 hours.
置於+40℃,相對濕度 95±5%環境中 240 小時
2.0N(0.204kg) for 30
Test conditions
Test conditions
seconds.
seconds.
KPEG006
90% min. stripped wires
shall be wet with
solder.(Except the edge of
terminal)
浸入裸線部份附著焊鍚 90%
以上.(末端斷面不算)
No damage and cutting off
線材不鬆動, 不脫落
No obstacle to be harmful
to normal operation;
damages, cracks, rusts and
distortions.
Should not be audible at
1.0V sine wave between
250Hz~4KHz
測試後無任何障礙防礙正常
操作.且在輸入 1.0V 正弦波
從 250Hz 到 4KHz 之間無異
常音
Being placed for 2 hours at
+25℃, receiver shall be
measured. No obstacle to
be harmful to normal
operation; damages,
cracks, rusts, etc.
Should not be audible at
1.0V, sine wave between
250 ~ 4KHz. S.P.L.
deviation of unit should be
within ±3.5dB
經測試後, 靜置於+25℃
（室溫） 環境中 2 小時後, 測
試後無任何障礙防礙正常操
作.且在輸入 1.0V 正弦波從
250 到 4KHz 之間無異常音
輸出音壓變化量在±3.5dB 內
Evaluation standard
Evaluation standard