E3-99-1261 SOUTHCO, E3-99-1261 Datasheet - Page 26

• Manufacturer Part Number: E3-99-1261
• Description: COMPRESSION LATCH, WING KNOB W/ LOCK
• Manufacturer: SOUTHCO

Specifications of E3-99-1261

• Svhc: No SVHC (18-Jun-2010)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

XX=05 •
XX=08 •
XX=00 •
XX=01 •
XX=04 •
XX=06 •
XX=07 •
XX=09 •
XX=02 •
XX=03 •
Pawl
Type
•
TOTAL
1 2
GRIP
Products identified with this symbol are stocked subject to prior sale in one or more of our global locations. If unavailable from our facility nearest you, allow for shipping time from another facility.
(1.06)
(1.30)
(1.14)
(1.38)
(1.46)
Mounting
(1.22)
(.83)
(.91)
(.98)
(.75)
Washer
21
23
25
27
33
19
29
31
35
37
PAWL TYPE NUMBERS
(.47)
(.63)
(.39)
(.31)
(.16)
0 (0)
(.71)
(.55)
(.24)
(.08)
12
16
10
18
14
Offset
8
4
6
2
Pawl
Mounting
Nut
XX=13 •
XX=11 •
XX=12 •
XX=10 •
XX=14
XX=18
XX=19
Pawl
XX=15
XX=16
XX=17
Type
TOTAL
GRIP
(2.01)
(2.09)
(1.53)
(1.61)
(1.85)
(1.93)
(2.24)
(1.69)
(1.77)
(2.17)
51
53
39
41
47
49
57
43
45
55
3
(.63)
(.71)
(.79)
(.16)
(.31)
(.08)
(.39)
(.24)
(.47)
(.55)
16
20
18
10
14
Offset
12
4
8
2
6
Pawl
(1.42 ± .15)
DOOR
These loads apply to latch assemblies only.
Retention to the panel is subject to user
method of installation and material.
1. Insert the latch through the rear of the
2. Adjust mounting nut so that the head of the
3. Place pawl on latch shaft and tighten pawl
Recommended tightening torque for the
Pawl Mounting Screw is 10 N•m (88.5 in-lbs).
HOUSING and CAP: Die-cast zinc, bright
chrome plated or powder coated, see table.
RETAINER and SPRING: 302 Stainless steel,
natural. O-RING: Buna-N rubber, natural.
CAM and SLEEVE: 1075 Case hardened
steel, zinc immersion coating. SHAFT
and SCREW: Low carbon steel, zinc plate,
chromate plus sealer. PIN: 1008 Steel,
zinc plated plus chromate dip. MOUNTING
WASHER, MOUNTING NUT and PAWL: 1010
steel, zinc plate, chromate plus sealer.
Maximum static load: 300 N (79 lbs.)
Average ultimate load: 700 N (157 lbs.)
36 ± 4
Dimensions without tolerances are for reference only.
door. Place the mounting washer then the
mounting nut onto the latch.
latch is flush with the outside of the door.
The holes in the washer and the nut must
be aligned. The latch must be aligned to
the latching position. Southco recommends
using a minimum of three mounting screws
in a pattern as shown above.
mounting screw while holding the pawl with
a 17 (.67) wrench.
Material and Finish
(To assist in your product selection; samples
Panel Preparation
Product Strength
FRAME
are available for your evaluation.)
Installation
Guidelines
THIS IS THE RECOMMENDED
HOLE PATTERN (120° APART).
USE M4 OR No. 8 MOUNTING
SCREWS (NOT SUPPLIED).
millimeter (inch)
millimeter
(inch)
(.87
22
Ø 33 ± 0.3 (1.30 ± .01)
CENTER LINE FOR
MOUNTING SCREWS
+ .008
- .000
+ 0.2
- 0.0
)
39