52801RJ9 FLUKE NETWORKS, 52801RJ9 Datasheet - Page 3

• Manufacturer Part Number: 52801RJ9
• Description: TEST SET, DTMF, LCD
• Manufacturer: FLUKE NETWORKS

Specifications of 52801RJ9

• Meter Display Type: LCD
• Network Functionality: DTMF
• Tone Generator: Built In
• Lan Tester Type: Data Line
• Kit Contents: TS52 PRO Test Set W/ ABN/PP And RJ11 Plug
• Rohs Compliant: NA

TS52 PRO Test Set Quick Guide
Feature
Data Test/ Lockout Override
Line Voltage Test
Loop Current Test
Redial the Last Number Dialed
Pulse Dialing
Program Speed Dial Numbers
Set Receive-Only Loud Speaker
as Default
(for use in noisy environments)
Speed Dial a Stored Number
Two-Way Speakerphone
Turn on visual ANAC mode
(For service provider use only, visual
ANAC not available in all regions)
Display and Backlight
DTMF Digit Grabbing
Caller ID
Polarity
Operation
Connect the unit to Tip and Ring and move the T/M switch to T. If high speed data is present, a warn-
ing beep sounds, the test set will lockout, will not go off-hook, and the display shows LOCKOUT. If
there is no high speed data, the unit will go off-hook. If the test set is locked out and you are certain
that you want to go off-hook, press the OVERRIDE key.
In Monitor mode, press the Vdc/mA TEST key.
Switch to Talk mode and press the Vdc/mA TEST key.
Switch to Talk mode and press the LNR key.
By default the unit is configured to Tone dial. Any time the test set goes off-hook, it is automatically
set to tone dialing. If you want to Pulse dial, switch to Talk mode and once off-hook, press the SHIFT
(STORE PROG) key and then the PULSE key to change the dialing mode to pulse dialing. You can then
enter the number to call.
Switch to Monitor mode and press RCL. Enter the number to be stored. Press STORE/PROG, then press
the number of the memory location (0-9) where you want to store it. The test set gives a confirmation
tone and the display shows STORED. Dialing a number from Speed Dial location 9 automatically puts
the test set into Visual ANAC mode and the test set is muted.
Switch to Monitor mode and press STORE/PROG, then press MUTE. The confirmation tone sounds. To
restore the Speakerphone as the default Speaker mode, repeat the above steps.
Switch to Talk mode and press RCL. Press the key (0-9) of the memory location where the number is
stored. The display shows the number being called.
Switch to Talk mode and press SPKR. Press SPKR again to deactivate. If you are listening only, press
MUTE to activate the Receive-Only Loud Speaker. Press MUTE again to restore the two-way Speaker-
phone.
You can get a visual ANAC DTMF response by putting the test set in visual ANAC mode. Use speed dial
location 9 or switch to Talk mode, press the STORE/PROG key and then the # key. When you dial your
ANAC number, the number that you are dialing from is shown on the display and the test set is muted.
Turn on the display by switching to Talk mode or press the VOL or Vdc/mA TEST key in Monitor mode.
Turn on or off the backlight in Monitor mode by pressing STORE/PROG followed by *. The default is off,
this conserves battery power.
Switch to Monitor mode, press the STORE/PROG key and then the Vdc/mA TEST key. Digit grabbing is
deactivated when the display times out.
The display shows the Caller ID (CID) after the first ring while in Monitor mode. The CID messages are:
•
•
•
•
•
If normal, no icon is displayed. If reversed, the icon is shown.
The incoming phone number
Blocked (if CID is blocked by the originating device)
Line error (CID data is incomplete)
Unknown ID (CID is not available)
Lines carrying high speed data and voice must have a splitter (filter) to detect Caller ID.
POL