F17734102901 Vishay, F17734102901 Datasheet - Page 9

• Manufacturer Part Number: F17734102901
• Description: Cap Film 0.1uF 253VAC PET 20% 9.5 X 19mm AXL Ammo Pack
• Manufacturer: Vishay

Specifications of F17734102901

• Package/case: 9.5(Max) X 19(Max)
• Mounting: Through Hole
• Capacitance Value: 0.1 uF
• Voltage: 253 Vac
• Dielectric: PET
• Product Length: 19(Max) mm
• Tolerance: 20 %
• Operating Temperature: -40 to 100 °C

F1773-2000
Vishay Roederstein
www.vishay.com
362
SUB-CLAUSE NUMBER AND TEST
4.12.3 Final measurements
SUB-GROUP C3
4.13.1 Initial measurements
4.13
4.14
4.14.7 Final measurements
SUB-GROUP C4
4.15
4.15.1 Initial measurements
Impulse voltage
Endurance
Charge and discharge
For technical questions, contact: [e-mail]
AC Capacitors, Suppression Capacitors
Class X2 AC 253 V (MKT) - Axial Type
Visual examination
Capacitance
Tangent of loss angle
Voltage proof
Insulation resistance
Capacitance
Tangent of loss angle:
3 successive impulses, full wave, peak
voltage:
X2: 2.5 kV for C ≤ 1 µF
X2: 2.5 kV/√C for C > 1 µF
Max. 24 pulses
Duration: 1000 h
1.25 x U
1.25 x U
Once in every hour the voltage is increased
to 1000 V
47 Ω ± 5 %
Visual examination
Capacitance
Tangent of loss angle
Voltage proof
Insulation resistance
10 000 cycles
Charged to 350 Vdc
Discharge resistance:
Capacitance
Tangent of loss angle:
R
for C > 1 µF at 1 kHz
For C ≤ 1 µF at 10 kHz or
For C ≤ 1 µF at 10 kHz or
for C > 1 µF at 1 kHz
1200 Vdc; 1 min between terminations
1200 Vdc; 1 min between terminations
2000 Vac; 1 min between terminations
and case
=
--------------------------------- -
2 x C (dU/dt)
Rac
Rac
RMS
350 Vdc
at 100 °C for C ≤ 1 µF
at 85 °C for C > 1 µF
for 0.1 s via resistor of
CONDITIONS
No visible damage
Legible marking
|ΔC/C| ≤ 5 % of the value measured in
4.12.1.
Increase of tan δ:
Compared to values measured in 4.12.1.
No permanent breakdown or flash-over
≥ 50 % of values specified in section
“Insulation resistance” of this specification
No self healing breakdowns or flashover
No visible damage
Legible marking
|ΔC/C| ≤ 10 % compared to values measured
in 4.13.1.
Increase of tan δ:
Compared to values measured in 4.13.1.
No permanent breakdown or flash-over
≥ 50 % of values specified in section
“Insulation resistance” of this specification
≤ 0. 008 for: C ≤ 1 µF or
≤ 0. 005 for: C > 1 µF
≤ 0.008 for: C ≤ 1 µF or
≤ 0.005 for: C > 1 µF
PERFORMANCE REQUIREMENTS
Document Number: 26507
Revision: 23-Sep-08