NW6006ASG Integrated Device Technology (Idt), NW6006ASG Datasheet - Page 2

• Manufacturer Part Number: NW6006ASG
• Description: Caller ID CMOS 3.58MHz 3V/5V 20-Pin SOIC
• Manufacturer: Integrated Device Technology (Idt)

Specifications of NW6006ASG

• Package: 20SOIC
• Telecommunication Standards Supported: ETSI/ETS-300 778-1|GR-30|SIN227|SIN242|SR-TSV-002476|TIA/EIA PN-4195|TIA/EIA-716|TIA/EIA-777
• Fabrication Technology: CMOS
• Maximum Data Rate: 1212 Bd
• Typical Operating Supply Voltage: 3|5 V
• Typical Supply Current: 2.5 mA
• Minimum Operating Temperature: -40 °C
• Maximum Operating Temperature: 85 °C
• Operating Frequency: 3.58 MHz

PIN INFORMATION
NW6006 ENHANCED TYPE II CALLER ID DECODER
WITH STUTTER DIAL TONE DETECTOR
OSCOUT
OSCIN
DCLK
DATA
Name
VREF
IN1+
GND
GS1
CB0
IN1-
Type
I/NC
O
O
O
O
I
I
-
I
I
Pin No.
10
1
2
3
4
5
6
7
8
9
Reference Voltage.
This output is used to bias the input OP amp. It is typically VCC/2.
Non-inverting Input of the gain adjustable Tip/Ring OP amp.
Inverting Input of the gain adjustable Tip/Ring OP amp.
Gain Select Output of the gain adjustable Tip/Ring OP amp.
The Tip/Ring signal can be attenuated or amplified at GS1 by adjusting the feedback resistor between GS1 and IN1-.
The FSK signal is always detected by Tip/Ring OP amp while DT-AS(CAS) signal can be detected by either Tip/Ring
or Hybrid OP amp. The OP amp selection is controlled by CB1 and CB2 bits.
Ground.
Oscillator Input.
A 3.579545 MHz crystal or ceramic resonator should be connected between this pin and the OSCOUT. It can also
be driven by an external clock source.
Oscillator Output.
A 3.579545 MHz crystal or ceramic resonator should be connected between this pin and the OSCIN. When an
external clock drives OSCIN, this pin can be left floating.
Control Bit 0 (FSK Data Interface Mode Select).
This pin can select the 3-wire FSK data interface mode. A ‘0’ on this pin indicates interface mode 0; while a ‘1’ on
this pin indicates interface mode 1. (The FSK data interface is consisted of DATA, DCLK and DR / STD pins.)
When CB0 is high and CB1, CB2 are both low, the device is set into the power down state.
Data Clock of the Serial FSK Interface.
In mode 0 (CB0 is low), this pin is unused; In mode 1 (CB0 is high), this pin is an input which clock the FSK data
byte out to the DATA pin.
Data Output of the Serial FSK Interface.
In mode 0 (CB0 is low), the FSK serial bit stream is output to the DATA pin directly.
In mode 1 (CB0 is high), the start bit is stripped off, the data byte and the stop bit is stored in a 9-bit buffer. At the
end of each word signaled by the DR / STD pin, the microcontroller should shift the byte out onto the DATA pin by
applying 8 read pulses to the DCLK pin. A 9
OSCOUT
OSCIN
DCLK
VREF
DATA
GND
IN1+
GS1
CB0
IN1-
Figure 2. Pin Assignment
1
2
3
4
5
6
7
8
9
10
2
th
DCLK pulse will shift out the stop bit for framing error checking.
20
19
18
17
16
15
14
13
12
11
Description
IN2+
IN2-
GS2
CB2
CB1
VCC
CD/STRDT
ST/GT
EST
DR/STD
INDUSTRIAL TEMPERATURE RANGE