D38999/20FA35SN Conesys, D38999/20FA35SN Datasheet
D38999/20FA35SN
Specifications of D38999/20FA35SN
Related parts for D38999/20FA35SN
D38999/20FA35SN Summary of contents
Page 1
... Self-locking quick coupling plug eliminates the need for lockwiring. Firewall Capability - Stainless steel shells in both K and S firewall classes are offered. www.conesys.com www.conesys.com Universal I/R Tool – A single, expendable plastic tool is used for both insertion and removal of contacts. Scoop-Proof Design – Recessed pins in elongated shells minimize the possibility for contact damage blind mating application, mating shells cannot “ ...
Page 2
... I 600 II 900 Note: The establishment of electrical safety factors is left entirely to the designer the best position to know www.conesys.com Performance Specifications Environmental Seal Wired, mated connectors with specified accessories attached, shall meet the altitude-immersion test specified in MIL-DTL-38999. Shell-to-Shell Conductivity Maximum potential drop shall not exceed: Classes F and ...
Page 3
... Spare Coax and Twinax contacts are not supplied. One insertion/extraction tool for each contact size is also included. www.conesys.com D38999 ...
Page 4
... H 1.689 42.90 1.375 34.93 1.250 J 1.811 46.00 1.500 38.10 1.375 www.conesys.com 31.50(1.240) G MAX D F MATING THREAD LOCKING INDICATOR BAND COLOR: RED Note 1: “K” Accessory Thread for AE320 is same as AE326 (“D” Accessory Thread) on page 41. Note 2: “F” Mating Thread for AE320 is same as AE326 (“ ...
Page 5
... H 2.063 52.40 1.562 39.67 1.969/1.796 J 2.189 55.60 1.687 42.85 2.017/1.939 www.conesys.com LOCKING INDICATOR BAND COLOR: RED C E MATING THREAD J THREAD HEX NUT PER D38999/28 Note 1: “K” Accessory Thread for AE324 is same as AE326 (“D” Accessory Thread) on page 41. Note 2: “ ...
Page 6
... F 1.516 38.50 G 1.642 41.70 H 1.768 44.90 J 1.890 48.00 www.conesys.com Self-Locking, RFI Grounding Plug 31.00(1.220) MAX BLUE COLOR BAND LOCATION OPTIONAL (REAR RELEASE) RFI STRIP E MATING THREAD Note : Maximum Grommet Extension for insert layouts incorporating size 8 and 10 contacts = 5.95(.234). B ...
Page 7
... (17) F (19 (21 (23 (25 www.conesys.com Keying Positions D° NORMAL MASTER KEYWAY A° B° C° 3. The angles for a given connector are the same whether it contains pin or socket inserts. 4. Insert arrangement does not rotate relative to the master keyway (key). Key/Keyway Positions A° 105 102 ...
Page 8
... F (19) 1.156 29.36 1.297 G (21) 1.250 31.75 1.422 H (23) 1.375 34.93 1.547 J (25) 1.500 38.10 1.672 www.conesys.com Flange and Jam Nut Receptacles Panel Cutouts B MIN For Front Mounting Minimum ±.005 mm inch mm inch 16.66 .516 13.11 .128 20.22 ...
Page 9
... MS3348 bushing required with 12 gauge wire. * When tested with silver-plated wire. ** Insertion tool is not required. *** Dummy contact, used in lieu of unwired contact and seal plug. www.conesys.com Socket Contacts Military No. Military No. M39029/56-348 M39029/56-351 M39029/56-352 M39029/56-353 M39029/75-416 M39029/103-559 M39029/56-527 M85049/81-10*** M39029/59-366 ...
Page 10
... M39029/58-528 M39029/56-527 For Coax and Twinax contacts refer to instructions that are supplied with contacts. www.conesys.com Contact Installation Instructions 3. Place the correct insertion tool on the contact so that the wire runs along the groove in the tool. (Tool tip will butt against the shoulder.) Hold the plug or receptacle body fi ...