D38999/20WC35PN Conesys, D38999/20WC35PN Datasheet - Page 2
![no-image](/images/no-image-200.jpg)
D38999/20WC35PN
Manufacturer Part Number
D38999/20WC35PN
Description
Conn MIL-DTL-38999 Circular PIN 22 POS Crimp ST Wall Mount 22 Terminal 1 Port
Manufacturer
Conesys
Type
MIL-DTL-38999 Circularr
Datasheet
1.D3899920FA35PN.pdf
(10 pages)
Specifications of D38999/20WC35PN
Gender
RCP
Termination Method
Crimp
Mounting
Wall Mount
Body Orientation
Straight
Performance Specifications
Operating Temperature Range
Classes F, K, S and BZ*: -65°C to +200°C (-85°F to +392°F)
Classes W and ZC*: -65°C to +175°C (-85°F to +347°F)
Material and Finish Data (Class)
F – aluminum shell, electroless nickel finish
K – stainless steel shell, passivated, firewall
S – stainless steel shell, electrodeposited nickel, firewall
W– aluminum shell, olive drab cadmium over nickel base
BZ* – aluminum nickel bronze shell, std insert
ZC*– aluminum shell, zinc cobalt finish
Corrosion Resistance
Classes K, W, BZ* and ZC* withstand 500-hour salt spray.
Classes F and S withstand 48-hour salt spray.
Durability
Minimum of 500 mating cycles.
Fluid Resistance
Connectors resist specified immersions in MIL-PRF-7808,
MIL-PRF-23699, MIL-PRF-5606, M2-V Chevron oil, Coolanol
25, MIL-DTL-83133 (JP-8), MIL-DTL-5624 (JP-4, JP-5),
SAE-AMS1424 Type I, and other solvents and cleaning agents.
Shielding Effectiveness
RFI and EMI attenuation at the specified frequencies meet
the requirements of MIL-DTL-38999.
G
G
Voltage Rating
Note:
entirely to the designer, as he is in the best position to know
www.conesys.com
RFI shielding effectiveness of mated connectors with RFI
backshells is measured in a triaxial radio frequency leakage
fixture.
EMI shielding effectiveness is measured at the interface
of mated connectors and tested by the mode-stirred
technique specified in method 3008 of MIL-STD-1344.
The establishment of electrical safety factors is left
Service
Rating
M
N
II
I
Suggested Operating Voltage
AC (RMS)
400
300
600
900
(Sea Level)
1250
550
450
850
DC
Test Voltage
Sea Level
–
V RMS
1300
1000
1800
2300
37
–
Environmental Seal
Wired, mated connectors with specified accessories
attached, shall meet the altitude-immersion test specified in
MIL-DTL-38999.
Shell-to-Shell Conductivity
Maximum potential drop shall not exceed:
G
G
Shock and Vibration Requirements
Wired, mated connectors shall not be damaged, nor shall
there be a current interruption longer than one microsecond
when subjected to the following:
Shock
Pulse of approximate half sine wave of 300 G ±15 percent mag-
nitude with duration of 3 ±1 milliseconds applied in three axes.
High Impact Shock
When mounted as specified in MIL-S-901, grade A, a drop
of a 400 lb. Hammer from 1 foot, 3 feet and 5 feet applied to
connector in three axes, totaling nine impacts.
Vibration
Wired and mated connectors withstand the following
vibration levels:
G
G
* Not on QPL, can be supplied to Aero-Electric part number only.
exactly what peak voltages, switching currents, transients, etc.,
can be expected in a particular circuit.
Classes F and S = 1.0 millivolt.
Class W = 2.5 millivolts, Class K = 10.0 millivolts
Sine vibration where connector samples with simulated
accessory load are subjected to simple harmonic motion
from 10 to 2,000 Hz in three mutually perpendicular axes,
in 20 minute sweeps, for 12 hours in each axis at velocity of
254 mm/sec from 10-50 Hz, displacement of 1.5 mm from
50-140Hz and acceleration of 60G from 140-2,000Hz.
Random Vibration per MIL-STD-1344, method 205,
test condition V at ambient temperature and test
condition VI, Letter “J” at elevated temperature.
Test Voltage
50,000 Ft.
Performance Specifications
V RMS
550
400
600
800
Test Voltage
70,000 Ft.
MIL-DTL-38999
V RMS
350
260
400
500
sales
Series III
@
aero-electric.com
Test Voltage
100,000 Ft.
V RMS
200
200
200
200