PTV12010WAD ARTESYN, PTV12010WAD Datasheet - Page 2

• Manufacturer Part Number: PTV12010WAD
• Description: Module DC-DC 1-OUT 1.2V to 5.5V 8A 44W 8-Pin
• Manufacturer: ARTESYN
• Type: Step Downr

Specifications of PTV12010WAD

• Output Current: 8 A
• Output Voltage: 1.2 to 5.5 V
• Input Voltage: 12 V
• Number Of Outputs: 1
• Output Power: 44 W

Part Number System with Options
1
2
3
4
5
6
7
N N o o t t e e s s
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
DC-DC CONVERTERS
OUTPUT
POWER
(MAX.)
Remote ON/OFF. Positive logic
ON:
OFF:
See Figures 1, 2, 3 and 6 for safe operating curves.
A 100 µF electrolytic input capacitor is required for proper operation as
well as a 10 µF high-frequency ceramic capacitor. The electrolytic
capacitor must be rated for the minimum rms of ripple current.
An external output capacitor is not required for basic operation. Adding
100 µF of distributed capacitance at the load will improve the transient
response.
1 A/µs load step, 50 to 100% I
If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point).
The pre-bias start-up feature is not compatible with Auto-Track™. This is
because when the module is under Auto-Track™ control, it is fully active
and will sink current if the output voltage is below that of a back-feeding
15 W
44 W
EFFICIENCY TABLE - PTV12010L (I
OUTPUT VOLTAGE
Pin 7 open; or V > 2 V
Pin 7 GND; or V < 0.6 V
10.8-13.2 Vdc
10.8-13.2 Vdc
VOLTAGE
Vo = 1.8 V
Vo = 1.5 V
Vo = 1.2 V
Vo = 1.0 V
Vo = 0.8 V
INPUT
Mechanical Package
Point of Load Alliance
POLA Non-isolated
Mounting Version
omax
Product Family
Output Current
Input Voltage
0.8-1.8 Vdc
1.2-5.5 Vdc
VOLTAGE
, C3 = 100 µF.
OUTPUT
Compatible
The ultra-wide output voltage trim range offers major advantages to users who
select the PTV12010. It is no longer necessary to purchase a variety of
modules in order to cover different output voltages. The output voltage can be
trimmed in a range of 1.2 Vdc to 5.5 Vdc for suffix ‘W’ and 0.8 Vdc to 1.8 Vdc
for suffix ‘L’. When the PTV12010 converter leaves the factory the output has
been adjusted to the default voltage of 1.2 V for the PTV12010W and 0.8 V for
PTV12010L.
V = Vertical
1 2 V i n s i n g l e o u t p u t
12 = 12 V
PTV12010
Always 0
01 = 8 A
EFFICIENCY
O O u u t t p p u u t t V V o o l l t t a a g g e e A A d d j j u u s s t t m m e e n n t t o o f f t t h h e e P P T T V V 1 1 2 2 0 0 1 1 0 0 S S e e r r i i e e s s
87%
86%
84%
81%
78%
O
= I
CURRENT
OUTPUT
OMAX
(MIN.)
0 A
0 A
P T V 1 2 0 1 0 W A H
)
CURRENT
(MAX.)
OUTPUT
8 A
8 A
(2)
8
9
10
source. Therefore to ensure a pre-bias hold-off, one of the following two
techniques must be followed when input power is first applied to the
module. The Auto-Track™ function must either be disabled, or the
module’s output held off using the Inhibit pin. Refer to Application Note
196 for more details.
The set-point voltage tolerance is affected by the tolerance and stability
of R set . The stated limit is unconditionally met if R set has a tolerance of
1% with 100/
To order Pb-free (RoHS compatible) through-hole parts replace the
mounting option ‘H’ with ‘D’, e.g. PTV12010WAD.
NOTICE: Some models do not support all options. Please contact your
local Artesyn representative or use the on-line model number search tool at
http://www.artesyn.com/powergroup/products.htm to find a suitable
alternative.
EFFICIENCY
(MAX.)
87%
92%
EFFICIENCY TABLE - PTV12010W (I
ºC or better temperature stability.
OUTPUT VOLTAGE
Vo = 5.0 V
Vo = 3.3 V
Vo = 2.5 V
Vo = 1.8 V
Vo = 1.5 V
Vo = 1.2 V
Mounting Style
D = Horizontal Through-Hole (Matte Sn)
H = Horizontal Through-Hole (Sn/Pb)
Pin Style
A = Through-Hole Std. Pin Length (0.150”)
Output Voltage Code
W = Wide
L = Low Voltage
±10 mV
±10 mV
LINE
REGULATION
File Name: ptv12010w.pdf Rev (02): 19 Dec 2005
±12 mV
±12 mV
(9)
LOAD
EFFICIENCY
NEW Product
92%
90%
88%
85%
83%
80%
O
NUMBER
= I
PTV12010W
PTV12010L
OMAX
MODEL
)
(9,10)
2