MAX7031MATJ50+ Maxim Integrated Products, MAX7031MATJ50+ Datasheet - Page 12

• Manufacturer Part Number: MAX7031MATJ50+
• Description: RF Receiver IC TXRX FSK W/PLL-EP 5MHz, and 433.92MHz
• Manufacturer: Maxim Integrated Products
• Type: Transceiverr

Specifications of MAX7031MATJ50+

• Package / Case: TQFN-32 EP
• Operating Frequency: 433.92 MHz
• Operating Supply Voltage: 2.7 V, 5 V
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The MAX7031 uses the two AGC control pins (AGC0
and AGC1) to enable or disable the AGC and set three
user-controlled dwell timer settings. The AGC dwell
time is dependent on the crystal frequency and the bit
settings of the AGC control pins. To calculate the dwell
time, use the following equation:
where K is an integer in decimal, determined by the
control pin settings shown in Table 1.
For example, a receiver operating at 315MHz has a
crystal oscillator frequency of 12.679MHz. For K = 11
(AGC setting = 0, 1), the dwell timer is 162µs; for K =
14 (AGC setting = 1, 0), the dwell timer is 1.3ms; for K
= 20 (AGC setting = 1, 1), the dwell time is 83ms.
A unique feature of the MAX7031 is the integrated
image rejection of the mixer. This eliminates the need
for a costly front-end SAW filter for many applications.
The advantage of not using a SAW filter is increased
sensitivity, simplified antenna matching, less board
space, and lower cost.
The mixer cell is a pair of double-balanced mixers that
perform an IQ downconversion of the RF input to the
10.7MHz intermediate frequency (IF) with low-side
injection (i.e., f
Table 1. AGC Dwell Time Settings for
MAX7031
Figure 1. FSK Demodulator PLL Block Diagram
12
AGC1
0
0
1
1
______________________________________________________________________________________
AGC0
Low-Cost, 308MHz, 315MHz, and 433.92MHz
LIMITING
AMPS
IF
0
1
0
1
LO
AGC disabled, high gain selected
K = 11, short dwell time
K = 14, medium dwell time
K = 20, long dwell time
Dwell Time
= f
DETECTOR
PHASE
RF
FSK Transceiver with Fractional-N PLL
- f
IF
). The image-rejection circuit
CHARGE
PUMP
DESCRIPTION
=
f
XTAL
2
K
FILTER
LOOP
TO FSK BASEBAND FILTER
AND DATA SLICER
10.7MHz VCO
2.0mV/kHz
Mixer
then combines these signals to achieve a typical 46dB
of image rejection over the full temperature range. Low-
side injection is required as high-side injection is not
possible due to the on-chip image rejection. The IF out-
put is driven by a source follower, biased to create a
driving impedance of 330Ω to interface with an off-chip
330Ω ceramic IF filter. The voltage conversion gain dri-
ving a 330Ω load is approximately 20dB. Note that the
MIXIN+ and MIXIN- inputs are functionally identical.
The MAX7031 utilizes a fixed integer-N PLL to generate
the receive LO. All PLL components, including the loop
filter, voltage-controlled oscillator, charge pump, asyn-
chronous 24x divider, and phase-frequency detector
are internal. The loop bandwidth is approximately
500kHz. The relationship between RF, IF, and reference
frequencies is given by:
The IF section presents a differential 330Ω load to pro-
vide matching for the off-chip ceramic filter. The internal
six AC-coupled limiting amplifiers produce an overall
gain of approximately 65dB, with a bandpass filter-type
response centered near the 10.7MHz IF frequency with
a 3dB bandwidth of approximately 10MHz. The RSSI
circuit demodulates the IF to baseband by producing a
DC output proportional to the log of the IF signal level
with a slope of approximately 15mV/dB.
The FSK demodulator uses an integrated 10.7MHz PLL
that tracks the input RF modulation and converts the
frequency deviation into a voltage difference. The PLL
is illustrated in Figure 1. The input to the PLL comes
from the output of the IF limiting amplifiers. The PLL
control voltage responds to changes in the frequency
of the input signal with a nominal gain of 2.0mV/kHz.
For example, an FSK peak-to-peak deviation of 50kHz
Figure 2. Sallen-Key Lowpass Data Filter
DS+
Integer-N, Phase-Locked Loop (PLL)
f
MAX7031
REF
= (f
Intermediate Frequency (IF)
RF
OP+
C
100kΩ
F2
- f
IF
)/24
DEMOD
FSK
DF
100kΩ
C
FSK Demodulator
F1