RX6501 RFM, RX6501 Datasheet
RX6501
Specifications of RX6501
Related parts for RX6501
RX6501 Summary of contents
Page 1
... The RX6501 employs RFM’s amplifier- sequenced hybrid (ASH) architecture to achieve this unique blend of characteristics. All critical RF functions are contained in the hybrid, simplifying and speeding design-in. The RX6501 is sensitive and stable. A wide dynamic range log detector provides robust performance in the presence of on-channel interference or noise. ...
Page 2
... Maximum Units dB dB µA 3.7 Vdc mV 10 P-P 85 ° Inches Min Nom Max .389 .395 .400 .265 .270 .275 .070 .076 .080 .065 .070 .075 .015 .020 .025 .035 .040 .045 .125 .130 .135 .055 .060 .065 Page RX6501 - 4/7/08 ...
Page 3
... Data Output Units Notes kbps see page 1& 2 µs single bit µs 4 bits of same value µF ±10% ceramic K ±5% µF ±5% K ±5% K ±1% K ±1%, typical values K ±5% K ±5% µF tantalum pF ±5% NPO nH 50 ohm antenna nH 50 ohm antenna Page RX6501 - 4/7/08 ...
Page 4
... RFA1 is ON (up to 50%). Since an amplifier-sequenced receiver is inherently a sampling SAW SAW Filter RFA1 Delay Line P1 Pulse Generator RF Data Pulse t PRI t PRC Figure 1 (RFA1 duty factor), where the 10 Detector & Data RFA2 Low-Pass Out Filter P2 Page RX6501 - 4/7/08 ...
Page 5
... RX6501 ASH Receiver Block Diagram RFA1 Antenna RFIO SAW CR Filter 20 ESD Choke receiver, the overall cycle time between the start of one RFA1 ON sequence and the start of the next RFA1 ON sequence should be set to sample the narrowest RF data pulse at least 10 times. Otherwise, significant edge jitter will be added to the detected data pulse ...
Page 6
... PW - 18.6, where µs and kilohms PW1 PW1 PW to ground at the LPFADJ LPF = 1445/R LPF LPF is in kilohms. LPF = 1750/f = 1.21*R FGD LPF in kHz, and R in kilohms. LPF LPF PR is given set PW2 , where f is LPF , where LPF Page RX6501 - 4/7/08 ...
Page 7
... LPF in kilohms user selected LPF in pF user selected BBO Page RX6501 - 4/7/08 ...
Page 8
... LPF is in kHz LPF to RREF. The threshold is TH1 can be adjusted between 0.1 and PRI is given by kilohms kilohms PR for internal BBO and BBC between this pin and from 4.5 kHz to 1.8 MHz. and 1.3* f LPF LPF from start-to-start PRC Page RX6501 - 4/7/08 ...
Page 9
... E-mail: info@rfm.com ©2008 by RF Monolithics, Inc. Description is set at 1.1 times the pulse width to the first RF amplifier). The ON pulse width t PW2 - 18.6, where µs and kilohms PW1 PW1 PW with a resistor R to ground (the ON pulse PW1 PW is given by: PW RX6501 - 4/7/08 PW1 Page ...
Page 10
... E-mail: info@rfm.com ©2008 by RF Monolithics, Inc. .435 0.000 Dimensions in inches. SM-20H PCB Pad Layout Note: Specifications subject to change without notice. .370 .345 .305 .265 .225 .185 .145 .105 .09 .065 RX6501 - 4/7/08 Page ...