ATA8202-PXQW19 Atmel, ATA8202-PXQW19 Datasheet - Page 6
![RF Receiver Switchable Rx-IC For Ind 433MHz](/photos/30/99/309934/qfn-24_sml.jpg)
ATA8202-PXQW19
Manufacturer Part Number
ATA8202-PXQW19
Description
RF Receiver Switchable Rx-IC For Ind 433MHz
Manufacturer
Atmel
Type
Receiverr
Datasheet
1.ATA8201-EK.pdf
(44 pages)
Specifications of ATA8202-PXQW19
Package / Case
QFN-24
Operating Frequency
435 MHz
Operating Supply Voltage
2.7 V to 3.3 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Noise Figure
7 dB
Supply Current
6.5 mA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
2. RF Receiver
2.1
6
Low-IF Receiver
ATA8201/ATA8202
As seen in
oscillator, and the signal processing part with mixer, IF filter, IF amplifier with analog RSSI,
FSK/ASK demodulator, data filter, and data slicer.
In receive mode, the LNA pre-amplifies the received signal which is converted down to a
440-kHz intermediate frequency (IF), then filtered and amplified before it is fed into an FSK/ASK
demodulator, data filter, and data slicer. The received signal strength indicator (RSSI) signal is
available at the pin RSSI.
The receive path consists of a fully integrated low-IF receiver. It fulfills the sensitivity, blocking,
selectivity, supply voltage, and supply current specification needed to design, e.g., an industrial/
aftermarket integrated receiver for RKE and TPM systems. A benefit of the integrated receive fil-
ter is that no external components needed.
At 315 MHz, the ATA8201 receiver (433.92 MHz for the ATA8202 receiver) has a typical system
noise figure of 6.0 dB (7.0 dB), a system I1dBCP of –31 dBm (–30 dBm), and a system IIP3 of
–24 dBm (–23 dBm). The signal path is linear for out-of-band disturbers up to the I1dBCP and
hence there is no AGC or switching of the LNA needed, and a better blocking performance is
achieved. This receiver uses an IF (intermediate frequency) of 440 kHz, the typical image rejec-
tion is 30 dB and the typical 3-dB IF filter bandwidth is 420 kHz (f
f
10 Kbits/s Manchester with ±38 kHz frequency deviation in FSK mode, thus, the resulting sensi-
tivity at 315 MHz (433.92 MHz) is typically –105 dBm (–104 dBm).
Due to the low phase noise and spurs of the synthesizer together with the 8th-order integrated IF
filter, the receiver has a better selectivity and blocking performance than more complex double
superhet receivers, without using external components and without numerous spurious receiv-
ing frequencies.
A low-IF architecture is also less sensitive to second-order intermodulation (IIP2) than direct
conversion receivers where every pulse or amplitude modulated signal (especially the signals
from TDMA systems like GSM) demodulates to the receiving signal band at second-order
non-linearities.
lo_IF
= 230 kHz and f
Figure 1-3 on page
hi_IF
= 650 kHz). The demodulator needs a signal-to-noise ratio of 8.5 dB for
5, the RF receiver consists of a low-noise amplifier (LNA), a local
IF
= 440 kHz ± 210 kHz,
4971C–INDCO–04/09