MAX2117CTI+T Maxim Integrated Products, MAX2117CTI+T Datasheet - Page 2

• Manufacturer Part Number: MAX2117CTI+T
• Description: RF Receiver Direct Conversion Tu ner for MMDS -75 to
• Manufacturer: Maxim Integrated Products

Specifications of MAX2117CTI+T

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Complete DBS Direct-Conversion Tuner ICs
with Monolithic VCOs
ABSOLUTE MAXIMUM RATINGS
V
All Other Pins to GND .................................-0.3V to (V
RFIN+ to RFIN-, XTL+ to XTL-, IDC+ to IDC-,
QDC+ to QDC- ...................................................................±2.0V
CNTOUT, XTALOUT, CPOUT, VREG1/2,
I/QOUT± to GND Short-Circuit Duration.................................10s
Continuous Current (any pin other than V
DC ELECTRICAL CHARACTERISTICS
(V
wise noted. Typical values are at V
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
2
SUPPLY
Supply Voltage
Supply Current
ANALOG GAIN CONTROL INPUT—GC1
Usable Voltage Range
Input Current
BASEBAND OUTPUTS— IOUT, QOUT (MAX2116)
Nominal Output Voltage Swing
Output Clipping Voltage
DC Output Voltage
BASEBAND OUTPUTS— IOUT±, QOUT± (MAX2118)
Nominal Output Voltage Swing
Output Clipping Voltage
Common-Mode Voltage
DC Offset Voltage
ANALOG OUTPUT— VREG1, VREG2
Output Voltage
Source Current
STATIC CONTROL INPUTS—AS2, AS1, AS0
Input Voltage High
Input Voltage Low
Input Current
SYNTHESIZER DC PARAMETERS
Charge Pump Source/Sink Current
CC
CC
_______________________________________________________________________________________
to GND ...........................................................-0.3V to +5.5V
= +4.75V to +5.25V, V
PARAMETER
GND
= 0V, V
CC
= +5V, T
GC1
CC
or GND) .......10mA
= +0.75V; no AC signal applied, default register settings, T
A
= +25°C, unless otherwise noted.) (Note 1)
LO locked at 2175MHz
0.75V < V
R
R
(differential) (Note 3)
Each output
Bits CP1 = 0, CP0 = 0
Bits CP1 = 0, CP0 = 1
Bits CP1 = 1, CP0 = 0
Bits CP1 = 1, CP0 = 1
LOAD
LOAD
CC
+ 0.3V)
= 1kΩ // 10pF (Note 3)
= 2kΩ // 10pF
GC1
< 2.6V (Note 2)
CONDITIONS
Continuous Power Dissipation (T
Operating Temperature Range ..............................0°C to +85°C
Junction Temperature .....................................................+150°C
Storage Temperature Range ............................-65°C to +160°C
Soldering Temperature (10s) ..........................................+300°C
40-Pin Thin QFN (derate 23.3mW/°C above +85°C) .... 1.86W
Bit DL = high
Bit DL = low
±140
±280
4.75
0.75
0.65
MIN
±35
±70
-50
-50
2.7
-50
4
A
A
= +85°C)
= 0°C to +85°C, unless other-
±100
±200
±400
TYP
0.59
0.75
2.85
195
±50
0.8
1.2
2
1
2
0
MAX
±136
±272
±544
5.25
0.85
3.05
265
+50
+50
+50
±68
2.6
0.5
3
UNITS
V
V
V
V
mA
mV
mA
µA
µA
µA
P-P
P-P
P-P
P-P
V
V
V
V
V
V
V